Differential and Bevel Gear - Disassemble
拆解步骤
Show/hide table
所需工具     | |||
工具     | 零件号     | 零件名称     | 数量     |
A     | 138-7573     | 连杆支架     | 2     |
B     | 2P-8312     | 挡圈钳     |     |
C     | 1P-0520     | 冲头总成     | 1     |
D     | 3S-6224     | 电动液压泵总成     | 1     |
1P-0820 | 液压拉拔器     | 1     | |
5F-7369 | 杆     | 2     | |
1B-4207 | 螺母     | 2     | |
3H-0465 | 推拉板     | 4     | |
8B-7551 | 轴承拉拔器总成     | 1     | |
E     | 138-7574     | 连杆支架     | 2     |
F     | 8S-6470     | 螺钉     | 3     |
G     | 3S-6224     | 电动液压泵总成     | 1     |
1P-0820 | 液压拉拔器     | 1     | |
3H-0468 | 拉拔器板     | 4     | |
1H-3110 | 轴承拉拔器总成     | 1     | |
1U-9889 | 十字挡块     | 1     | |
1A-1935 | 全高螺母     | 2     | |
3H-0469 | 支腿     | 2     | |
H     | 5P-1730     | 护圈     | 1     |
J     | 5V-0490     | 拉拔器螺栓     | 2     |
K     | 138-7575     | 连杆支架     | 2     |
L     | 5P-7311     | 拉拔器     | 1     |
7S-7786 | 支腿     | 2     | |
M     | 3S-6224     | 电动液压泵总成     | 1     |
1P-0820 | 液压拉拔器     | 1     | |
1H-3110 | 轴承拉拔器总成     | 1     | |
1U-9889 | 十字挡块     | 1     | |
3H-0468 | 鞍座     | 4     | |
1A-1935 | 全高螺母     | 2     | |
1H-3108 | 推拉支腿     | 2     |
开始:
- 分离差速器和伞齿轮与变速箱。 请参阅拆解和组装, "变速箱与差速器 - 分离"。
注: 清洁度是一项重要的因素。 拆解步骤开始之前,应彻底清洁部件外部。 这将有助于防止脏污进入内部机构。
注: 为便于组装,在部件上做出识别标记。
- 断开夹子 (2) 。 卸下软管组件 (1) 。
Show/hide table
图 1 | g01296975 |
- 将工具 (A) 和适当的起吊设备连接在差速器锁组件 (3) 上。 差速器锁组件 (3) 的重量约为 54 kg (120 lb)。
Show/hide table
图 2 | g01296976 |
- 松开螺栓 (4) ,卸下差速器锁组件 (3) 。
Show/hide table
图 3 | g01296979 |
- 均匀地卸下螺栓 (5) ,释放弹簧压力。 从油缸 (7) 上卸下壳体 (6) 。
Show/hide table
图 4 | g01296980 |
Show/hide table
被弹簧力爆出的零件击中,会招致人员伤害。 确保穿上所有必要的保护装备。 遵照建议的程序,并使用所有建议的工具以释放弹簧力。 |
- 如有必要,从壳体 (6) 上卸下定位销 (8) 。
Show/hide table
图 5 | g01296981 |
- 从活塞 (10) 上卸下弹簧 (9) 。
Show/hide table
图 6 | g01296982 |
Show/hide table
图 7 | g01296984 |
- 使用适当的支座支撑离合器夹爪 (12) 。 使用工具 (B) ,卸下挡圈 (13) 。 卸下隔套 (14) 。 从油缸 (11) 上卸下离合器夹爪 (12) 。
- 从离合器夹爪 (12) 上卸下垫圈 (15) 。
Show/hide table
图 8 | g01296986 |
- 卸下垫圈 (16) 。
Show/hide table
图 9 | g01296987 |
- 使用适当的支座支撑油缸 (11) 。 使用工具 (C) ,卸下活塞 (17) 。
Show/hide table
图 10 | g01296989 |
- 卸下 O 形密封圈 (18) 。 卸下环 (19) 。
Show/hide table
图 11 | g01296994 |
- 卸下螺栓 (20) 、保持架 (21) 和垫片 (22) 。
Show/hide table
图 12 | g01296995 |
- 使用适当的压具,卸下轴承外圈 (23) 。
Show/hide table
图 13 | g01296999 |
- 卸下小齿轮 (24) 。
Show/hide table
图 14 | g01296996 |
Show/hide table
图 15 | g01296998 |
- 使用工具 (D) ,从小齿轮 (24) 两侧卸下轴承内圈 (25) 。
- 将工具 (A) 和适当的起吊设备连接在轴承盖 (26) 上。 轴承盖 (26) 的重量约为 27 kg (60 lb)。 卸下锁 (28) 。 卸下螺栓 (29) 。 卸下轴承盖 (26) 。 卸下其余的螺栓 (4) 。 使用适当的压具,卸下轴承外圈 (27) 。
Show/hide table
图 16 | g01297000 |
Show/hide table
图 17 | g01297003 |
- 卸下锁紧钢丝 (30) 。 卸下螺栓 (31) 。 卸下离合器夹爪 (32) 。
Show/hide table
图 18 | g01297004 |
- 卸下锁 (33) 。 卸下螺栓 (34) 。 卸下轴承盖 (35) 。
Show/hide table
图 19 | g01297006 |
- 将适当的起吊设备连接在差速器组件 (37) 和伞齿轮组件 (36) 上。 差速器组件 (37) 和伞齿轮组件 (36) 的重量约为 254 kg (560 lb)。 卸下调整环 (38) 和轴承外圈 (39) 。
Show/hide table
图 20 | g01297514 |
- 升起差速器组件 (37) 和伞齿轮组件 (36) ,卸下轴承保持架 (40) 。
Show/hide table
图 21 | g01299179 |
- 卸下其余的螺栓 (4) 。
Show/hide table
图 22 | g01297517 |
- 将工具 (E) 和适当的起吊设备连接在差速器组件 (37) 和伞齿轮组件 (36) 上。 差速器组件 (37) 和伞齿轮组件 (36) 的重量约为 254 kg (560 lb)。 将差速器组件 (37) 和伞齿轮组件 (36) 安置在适当的支座上。
Show/hide table
图 23 | g01297519 |
- 卸下螺母 (41) 。
Show/hide table
图 24 | g01297521 |
- 如图所示,将适当的起吊设备连接在差速器组件 (37) 上。 差速器组件 (37) 和伞齿轮组件 (36) 的重量约为 254 kg (560 lb)。 使用工具 (F) ,分离差速器组件 (37) 与伞齿轮组件 (36) 。
Show/hide table
图 25 | g01297524 |
- 卸下螺母 (42) 。
Show/hide table
图 26 | g01297526 |
- 将适当的起吊设备连接在差速器壳体 (43) 上。 差速器壳体 (43) 的重量约为 56 kg (125 lb)。 卸下差速器壳体 (43) 。
Show/hide table
图 27 | g01297527 |
- 使用工具 (G) ,卸下轴承内圈 (44) 。
Show/hide table
图 28 | g01297528 |
- 卸下垫圈 (45) 。 卸下齿轮 (46) 。
Show/hide table
图 29 | g01297530 |
- 将适当的起吊设备连接在差速器十字轴组件 (47) 上。 差速器十字轴组件 (47) 的重量约为 45 kg (100 lb)。 卸下差速器十字轴组件 (47) 。 从差速器十字轴组件 (47) 上卸下差速器小齿轮 (48) 。
Show/hide table
图 30 | g01297532 |
- 将工具 (H) 安置在适当的台钳上。 将差速器小齿轮 (48) 安装在工具 (H) 上。 弯曲垫圈 (49) 上的锁舌。 卸下螺母 (50) 和垫圈 (49) 。 卸下轴承内圈 (51) 和差速器小齿轮 (48) 。
Show/hide table
图 31 | g01297534 |
- 卸下轴承外圈 (52) 。
Show/hide table
图 32 | g01297535 |
- 卸下隔套 (54) 。 从护圈 (53) 上卸下轴承内圈 (55) 。
Show/hide table
图 33 | g01297539 |
- 卸下齿轮 (56) 。
Show/hide table
图 34 | g01297540 |
- 卸下垫圈 (57) 。 卸下螺栓 (58) 。
Show/hide table
图 35 | g01297541 |
- 如图所示,需要两个人,安置壳体组件 (60) 。 壳体组件 (60) 的重量约为 31 kg (70 lb)。 使用工具 (G) ,卸下轴承内圈 (59) 。
Show/hide table
图 36 | g01297553 |
- 卸下螺栓 (61) 。 卸下支架 (62) 。 卸下管组件 (63) 。
Show/hide table
图 37 | g01297557 |
- 分离支架 (62) 与管组件 (63) 。 卸下 O 形密封圈 (64) 。
Show/hide table
图 38 | g01297559 |
- 卸下螺栓 (65) 。
Show/hide table
图 39 | g01297561 |
- 安装工具 (J) ,分离保持架组件 (66) 与壳体 (67) 。
Show/hide table
图 40 | g01297563 |
- 将工具 (K) 和适当的起吊设备连接在保持架组件 (66) 上。 保持架组件 (66) 的重量约为 29 kg (65 lb)。 卸下保持架组件 (66) 。 卸下垫片 (68) 。
Show/hide table
图 41 | g01297564 |
- 卸下轴承外圈 (69) 。 卸下密封 (70) 。 卸下 O 形密封圈 (71) 。
Show/hide table
图 42 | g01298830 |
- 将工具 (L) 和适当的起吊设备连接在小齿轮 (72) 上。 小齿轮 (72) 的重量约为 48 kg (105 lb)。 卸下小齿轮 (72) 。
Show/hide table
图 43 | g01298838 |
- 使用工具 (M) ,从小齿轮 (72) 上卸下轴承内圈 (74) 。 卸下承磨套筒 (73) 。
Show/hide table
图 44 | g01298839 |
- 卸下轴承外圈 (75) 。
Show/hide table
图 45 | g01298842 |
Caterpillar Information System:
992K Wheel Loader Axle Oscillation Bearings - Lubricate
2007/10/15 A New Procedure for the Location and Adjusting the Bucket Stop is Now Available {6001, 6107, 6119}
D7G and D7G Series II Track-Type Tractors Power Train Gear Pump (Transmission) - Assemble
D7G and D7G Series II Track-Type Tractors Power Train Gear Pump (Transmission) - Disassemble
2006/10/23 Improved Head Gasket {1100, 1124}
2006/10/30 Replacement Flash File for Low Oil Pressure and Elevated Idle {1902, 7620}
2006/09/04 A New Torque Specification For the Cap Nuts on Fuel Injectors is Now Used {1251, 1254, 1290, 1713}
816F Series 2 Landfill Compactor, 815F Series 2 Soil Compactor and 814F Series 2 Wheel Dozer Diagnostic Capabilities
816F Series 2 Landfill Compactor, 815F Series 2 Soil Compactor and 814F Series 2 Wheel Dozer Event Code List
992K Wheel Loader Articulation Bearings - Lubricate
854K Wheel Dozer Capacities (Refill)
816F Series 2 Landfill Compactor, 815F Series 2 Soil Compactor and 814F Series 2 Wheel Dozer Switch Circuits
D6N Track-Type Tractor Hydraulic System Piston Pump (Implement) - Test and Adjust
657G Wheel Tractor-Scraper Wheel Tractor Power Train Transfer Gears - Disassemble
657G Wheel Tractor-Scraper Wheel Tractor Power Train Transfer Gears - Assemble
D6G Series II Track-Type Tractor Machine Systems Gear Pump (Implement) - Disassemble
D6G Series II Track-Type Tractor Machine Systems Gear Pump (Implement) - Assemble
834H Wheel Dozer and 836H Landfill Compactor Sound Information and Vibration Information
C175-16 Locomotive Engine ECM - Replace
657G Wheel Tractor-Scraper Wheel Tractor Power Train Torque Converter - Disassemble
816F Series 2 Landfill Compactor, 815F Series 2 Soil Compactor and 814F Series 2 Wheel Dozer Connector Contact Description
D6N Track-Type Tractor Hydraulic System Ripper Control
Retrofit To SystemOne Track Guiding Arrangements{4177} Retrofit To SystemOne Track Guiding Arrangements{4177}
657G Wheel Tractor-Scraper Wheel Tractor Power Train Torque Converter - Assemble