Transfer Gears - Assemble
组装步骤
Show/hide table
所需工具     | |||
---|---|---|---|
工具     | 零件号     | 零件名称     | 数量     |
C     | 1P-0520     | 冲头总成     | 1     |
D     | 8H-8581     | 塞尺     | 1     |
E     | 1P-0770     | 密封导套     | 1     |
1P-0510 | 冲头总成     | 1     | |
F     | 138-7576     | 连杆支架     | 2     |
4C-9634 | 拉拔器螺柱     | 1     | |
2K-7468 | 锁紧螺母     | 2     | |
1P-1838 | 轴承拉拔器适配器     | 1     | |
6V-6042 | 千分表指针总成     | 1     | |
8T-5096 | 千分表总成     | 1     | |
G     | 138-7576     | 连杆支架     | 2     |
4C-9633 | 拉拔器螺柱     | 1     | |
1A-1935 | 全高螺母     | 2     | |
5P-8601 | 轴承拉拔器适配器     | 1     | |
8S-6587 | 接头     | 1     | |
6V-6042 | 千分表指针总成     | 1     | |
8T-5096 | 千分表总成     | 1     |
- 冷却轴承外圈 (27) 和 (29) 。 将隔套 (28) 、轴承外圈 (27) 和 (29) 安装到分动器 (23) 上。
Show/hide table
图 1 | g01300608 |
注: 组装后,必须对齐分动器 (23) 与轴承外圈 (27) 和 (29) 。
- 将轴承内圈 (24) 和 (26) 以及隔套 (25) 安装到分动器 (23) 上。
Show/hide table
图 2 | g01300606 |
- 安装分动器 (23) 。
Show/hide table
图 3 | g01300605 |
- 安装轴 (21) 。 使用工具 (D) ,在四个点测量间隙。 安装垫片 (22) (图上未显示),使厚度比平均间隙测量值小 0.25 ± 0.05 mm (0.010 ± 0.002 in)。
Show/hide table
图 4 | g01301275 |
- 安装螺栓 (20) 。
Show/hide table
图 5 | g01301021 |
- 使用工具 (C) ,安装滚球轴承 (19) (图上未显示)。
Show/hide table
图 6 | g01301027 |
- 使用工具 (E) 和适当的压具,安装轴承保持架 (18) 。
Show/hide table
图 7 | g01301276 |
- 安装挡圈 (17) 。
Show/hide table
图 8 | g01301023 |
- 使用工具 (C) ,安装轴承外圈 (14) 。
Show/hide table
图 9 | g01300555 |
- 加热轴承内圈 (13) 。 将轴承内圈 (13) 安装到分动器 (12) 上。
Show/hide table
图 10 | g01301029 |
- 安装分动器 (12) 。
Show/hide table
图 11 | g01300553 |
- 安装泵驱动齿轮 (11) 和螺栓 (10) 。 拧紧螺栓 (10) 至扭矩为 50 ± 3 N·m (37 ± 2 lb ft)。
Show/hide table
图 12 | g01301032 |
- 安装轴承外圈 (9) 。
Show/hide table
图 13 | g01301279 |
- 安装轴承保持架 (8) 和螺栓 (7) 。 拧紧螺栓 (7) 至扭矩为 50 ± 3 N·m (37 ± 2 lb ft)。
Show/hide table
图 14 | g01301296 |
- 使用工具 (F) 和适当的起吊设备,测量轴承的轴向间隙。 根据需要,安装垫片,以获得 0.15 ± 0.05 mm (0.006 ± 0.002 in) 的轴承轴向间隙。
Show/hide table
图 15 | g01301297 |
- 使用工具 (C) ,安装轴承外圈 (6) 。
Show/hide table
图 16 | g01301298 |
Show/hide table
图 17 | g01300527 |
- 安装泵驱动齿轮 (16) 和螺栓 (15) 。 拧紧螺栓 (15) 至扭矩为 50 ± 3 N·m (37 ± 2 lb ft)。
Show/hide table
图 18 | g01301028 |
- 加热轴承内圈 (5) 。 将轴承内圈 (5) 和挡圈 (3) 安装到分动器 (4) 上。
Show/hide table
图 19 | g01301036 |
- 安装分动器 (4) 。
Show/hide table
图 20 | g01301325 |
- 冷却轴承外圈 (1) 。 将轴承外圈 (1) 安装到保持架组件 (2) 上。
Show/hide table
图 21 | g01301037 |
- 安装保持架组件 (2) 。
Show/hide table
图 22 | g01301326 |
- 使用工具 (G) 和适当的起吊设备,测量轴承的轴向间隙。 根据需要,安装垫片,以获得 0.15 ± 0.05 mm (0.006 ± 0.002 in) 的轴承轴向间隙。
Show/hide table
图 23 | g01301328 |
End By: 安装分动器。 请参阅 拆解和组装, "分动器 - 安装"。
Caterpillar Information System:
657G Wheel Tractor-Scraper Wheel Tractor Power Train Transfer Gears - Disassemble
D6N Track-Type Tractor Hydraulic System Piston Pump (Implement) - Test and Adjust
657G Wheel Tractor-Scraper Wheel Tractor Power Train Differential and Bevel Gear - Disassemble
992K Wheel Loader Axle Oscillation Bearings - Lubricate
2007/10/15 A New Procedure for the Location and Adjusting the Bucket Stop is Now Available {6001, 6107, 6119}
D7G and D7G Series II Track-Type Tractors Power Train Gear Pump (Transmission) - Assemble
D7G and D7G Series II Track-Type Tractors Power Train Gear Pump (Transmission) - Disassemble
2006/10/23 Improved Head Gasket {1100, 1124}
2006/10/30 Replacement Flash File for Low Oil Pressure and Elevated Idle {1902, 7620}
2006/09/04 A New Torque Specification For the Cap Nuts on Fuel Injectors is Now Used {1251, 1254, 1290, 1713}
816F Series 2 Landfill Compactor, 815F Series 2 Soil Compactor and 814F Series 2 Wheel Dozer Diagnostic Capabilities
816F Series 2 Landfill Compactor, 815F Series 2 Soil Compactor and 814F Series 2 Wheel Dozer Event Code List
D6G Series II Track-Type Tractor Machine Systems Gear Pump (Implement) - Disassemble
D6G Series II Track-Type Tractor Machine Systems Gear Pump (Implement) - Assemble
834H Wheel Dozer and 836H Landfill Compactor Sound Information and Vibration Information
C175-16 Locomotive Engine ECM - Replace
657G Wheel Tractor-Scraper Wheel Tractor Power Train Torque Converter - Disassemble
816F Series 2 Landfill Compactor, 815F Series 2 Soil Compactor and 814F Series 2 Wheel Dozer Connector Contact Description
D6N Track-Type Tractor Hydraulic System Ripper Control
Retrofit To SystemOne Track Guiding Arrangements{4177} Retrofit To SystemOne Track Guiding Arrangements{4177}
657G Wheel Tractor-Scraper Wheel Tractor Power Train Torque Converter - Assemble
2006/08/28 New Hose Improves Reliability {4257, 4269}
D6G Series II Track-Type Tractor Engine Supplement Engine and Torque Converter - Install
992K Wheel Loader Drive Shaft Support Bearing - Lubricate