Grapple Arch (Dual Function) - Install
Note: Cleanliness is an important factor. Before assembly, all parts should be thoroughly cleaned in cleaning fluid. Allow the parts to air dry. Wiping cloths or rags should not be used to dry parts. Lint may be deposited on the parts which may cause later trouble. Inspect all parts. If any parts are worn or damaged, use new parts for replacement.
- Lower the temperature of bearings (9) and install bearing (9) on both sides.
Show/hide table
Illustration 2 g01272324 - Use a suitable lifting device to position grapple arch (2) on the machine. The weight of grapple arch (2) is approximately
658 kg (1450 lb) .Show/hide tableIllustration 3 g01272364 - Install pin assembly (8) and bolt (7). Repeat this Step for the other side of grapple arch (2).
- Use the suitable lifting device to raise the grapple arch into position.
Show/hide table
Illustration 4 g01272322 - Connect arch cylinder (4) and install pin assembly (5) and bolt (6). Repeat this Step for the other arch cylinder.
Show/hide table
Illustration 5 g01272320 - Remove the suitable blocking that was used to support arch cylinder (4). Repeat this Step for the other side.
Show/hide table
Illustration 6 g01272319 - Remove the suitable lifting device from grapple arch (2).
- Remove pin assemblies (3).
Show/hide table
Illustration 7 g01272318 - Connect hose assemblies (1) on both sides of the machine.
Show/hide table
Illustration 1 | g01272365 |
End By:
- Install the grapple boom. Refer to Disassembly and Assembly, "Grapple Boom (Dual Function) - Install".
Caterpillar Information System:
525C, 535C and 545C Wheel Skidders Machine Systems Grapple Arch (Dual Function) - Remove
525C, 535C and 545C Wheel Skidders Machine Systems Grapple Boom (Dual Function) - Install
525C, 535C and 545C Wheel Skidders Machine Systems Grapple Boom (Dual Function) - Remove
C11 and C13 Engines for Caterpillar Built Machines Inlet Manifold - Remove
C11 and C13 Engines for Caterpillar Built Machines Inlet Manifold - Install
854K Wheel Dozer Cooling System Coolant Level - Check
854K Wheel Dozer Transmission Oil Sample - Obtain
D6N Track-Type Tractor Hydraulic System Piston Motor (Steering)
525C, 535C and 545C Wheel Skidders Power Train Transmission - Assemble
525C, 535C and 545C Wheel Skidders Power Train Transmission - Disassemble
D6N Track-Type Tractor Hydraulic System Lift Cylinder (Ripper)
D6N Track-Type Tractor Hydraulic System Angle Cylinder (Bulldozer)
854K Wheel Dozer Cooling System Coolant Extender (ELC) - Add
3508 EUI Engine for Off-Highway Truck/Tractors Engine Oil Filter Base
D6N Track-Type Tractor Hydraulic System Piston Pump (Implement)
EquipmentManager User Guide Manage Equipment Groups
3508 EUI Engine for Off-Highway Truck/Tractors Engine Oil Pan
525C Wheel Skidder, 535C Wheel Skidder and 545C Wheel Skidder Power Train Transmission Hydraulic Control
D8T, D9T, D10T and D11T Track-Type Tractors Fast Fill Fuel System - D8T, D9T, D10T and D11T
525C, 535C and 545C Wheel Skidders Machine Systems Front Frame from Rear Frame - Separate
525C, 535C and 545C Wheel Skidders Machine Systems Front Frame to Rear Frame - Connect
657G Wheel Tractor-Scraper Steering System Relief Valve (Steering Cylinder Crossover) - Test and Adjust
993K Wheel Loader Fuses - Replace
Relocation of Primary Fuel/Water Separator with Winch Arrangement{1260, 1263} Relocation of Primary Fuel/Water Separator with Winch Arrangement{1260, 1263}