Engine Oil Filter Base
Show/hide table
Illustration 1 | g01272386 |
(1) Clamp bolt
Use the following bolt tightening sequence in order to tighten the clamp bolts.
- Place the clamp assembly so that the clamp assembly is snug against the tube.
- Tighten the clamp assembly to the adapter.
Torque ... 47 ± 9 N·m (35 ± 7 lb ft)
- Tighten the clamp assembly to the tube.
Torque ... 47 ± 9 N·m (35 ± 7 lb ft)
(2) Stud
-
Apply 154-9731 Thread Lock Compound to the last 10.2 ± 1.5 mm (.40 ± .06 inch) of the thread at the base end of the stud.
- Torque ... 80 ± 14 N·m (60 ± 10 lb ft)
(3) Oil filter
- Put clean engine oil on the oil filter seal.
- Put oil filter (3) in position and tighten the oil filter until the seal contacts the oil filter base.
- Tighten the filter for an additional 360 degrees.
(4) Oil filter bypass valve
- The oil filter bypass valves must open at the following pressure difference: ... 230 ± 20 kPa (33 ± 3 psi)
(5) 7G-6713 Spring for the oil filter bypass valves
- Length under test force ... 57.2 mm (2.25 inch)
- Test force ... 109 ± 5 N (24.5 ± 1.1 lb)
- Free length after test ... 99.7 mm (3.93 inch)
- Outside diameter ... 21.23 mm (0.836 inch)
- Color code (stripes) ... one light blue stripe
- Test force ... 109 ± 5 N (24.5 ± 1.1 lb)
Caterpillar Information System:
854K Wheel Dozer Cooling System Coolant Extender (ELC) - Add
525C, 535C and 545C Wheel Skidders Machine Systems Grapple Arch (Dual Function) - Install
525C, 535C and 545C Wheel Skidders Machine Systems Grapple Arch (Dual Function) - Remove
525C, 535C and 545C Wheel Skidders Machine Systems Grapple Boom (Dual Function) - Install
525C, 535C and 545C Wheel Skidders Machine Systems Grapple Boom (Dual Function) - Remove
C11 and C13 Engines for Caterpillar Built Machines Inlet Manifold - Remove
C11 and C13 Engines for Caterpillar Built Machines Inlet Manifold - Install
854K Wheel Dozer Cooling System Coolant Level - Check
854K Wheel Dozer Transmission Oil Sample - Obtain
D6N Track-Type Tractor Hydraulic System Piston Motor (Steering)
525C, 535C and 545C Wheel Skidders Power Train Transmission - Assemble
525C, 535C and 545C Wheel Skidders Power Train Transmission - Disassemble
D6N Track-Type Tractor Hydraulic System Piston Pump (Implement)
EquipmentManager User Guide Manage Equipment Groups
3508 EUI Engine for Off-Highway Truck/Tractors Engine Oil Pan
525C Wheel Skidder, 535C Wheel Skidder and 545C Wheel Skidder Power Train Transmission Hydraulic Control
D8T, D9T, D10T and D11T Track-Type Tractors Fast Fill Fuel System - D8T, D9T, D10T and D11T
525C, 535C and 545C Wheel Skidders Machine Systems Front Frame from Rear Frame - Separate
525C, 535C and 545C Wheel Skidders Machine Systems Front Frame to Rear Frame - Connect
657G Wheel Tractor-Scraper Steering System Relief Valve (Steering Cylinder Crossover) - Test and Adjust
993K Wheel Loader Fuses - Replace
Relocation of Primary Fuel/Water Separator with Winch Arrangement{1260, 1263} Relocation of Primary Fuel/Water Separator with Winch Arrangement{1260, 1263}
2006/05/22 Replacing Both Hydrostatic Pumps Restores Straight Tracking {5070}
525C Wheel Skidder, 535C Wheel Skidder and 545C Wheel Skidder Power Train Transmission Control Valve