Cab - Install
安装步骤
Show/hide table
所需工具     | |||
---|---|---|---|
工具     | 零件号     | 零件描述     | 数量     |
A     | FT2943     | 隔套     | 2     |
138-7575 | 连杆支架     | 4     | |
B     | 5P-3975     | 橡胶润滑剂     |     |
- 将工具 (A) 和适当的起吊设备安装到驾驶室 (33) 上。 驾驶室 (33) 的重量约为 862 kg (1900 lb)。
Show/hide table
图 1 | g01064113 |
- 将驾驶室安置到橡胶座和机器上。
- 安装套筒前,将工具 (B) 涂敷到橡胶座的内部。 拧紧螺栓 (35) 和 (34) 前,确保套筒正确对准。
Show/hide table
图 2 | g01064187 |
Show/hide table
图 3 | g01064115 |
- 将螺栓 (35) 安装到驾驶室后部。 拧紧螺栓 (35) 。
- 将螺栓 (34) 安装到驾驶室前部。 拧紧螺栓 (34) 。
- 再次拧紧螺栓 (35) 和 (34) 。
- 安置电缆组件 (31) 。 安装销 (29) 、卡箍 (32) 和夹子 (30) 。
Show/hide table
图 4 | g01064026 |
- 安置存储箱 (28) ,然后安装螺钉 (27) 。
Show/hide table
图 5 | g01062651 |
- 连接电缆组件 (26) ,然后安装螺母 (25) 。
Show/hide table
图 6 | g01062650 |
- 安置盖组件 (24) ,然后安装螺钉 (23) 。
Show/hide table
图 7 | g01062643 |
- 安置计量泵 (22) ,然后安装螺栓 (21) 。
Show/hide table
图 8 | g01062630 |
Show/hide table
图 9 | g01062629 |
- 安装地板垫 (20) 。
Show/hide table
图 10 | g01062590 |
- 安置阀组件 (19) ,然后安装螺栓 (17) 。 连接线束组件 (18) 。
Show/hide table
图 11 | g01062589 |
- 连接接地母线组件 (15) 和线束组件 (16) 。
Show/hide table
图 12 | g01062588 |
- 连接线束组件 (14) 。
Show/hide table
图 13 | g01062587 |
- 安置防护罩组件 (13) ,然后安装螺栓 (12) 。
Show/hide table
图 14 | g01062586 |
- 连接软管组件 (11) 。
Show/hide table
图 15 | g01062584 |
- 安置盖 (10) ,然后安装螺钉 (9) 。
Show/hide table
图 16 | g01062582 |
Show/hide table
图 17 | g01062583 |
- 安装护线圈 (8) 。
Show/hide table
图 18 | g01062579 |
- 向外转动操纵杆 (4) ,如图所示。 拧紧螺母 (5) 。
Show/hide table
图 19 | g01062575 |
- 安装操纵杆 (6) 和板 (7) 。
- 连接软管 (3) 。
Show/hide table
图 20 | g01062574 |
- 连接软管 (2) 。
Show/hide table
图 21 | g01062572 |
- 连接软管组件 (1) 。
Show/hide table
图 22 | g01062571 |
- 使用冷却液加注冷却系统。 请参考操作和维护手册, "加注容量"。
- 为空调系统加注空调制冷剂。 请参考维修手册, SENR5664, "使用 R-134a 制冷剂的空调与暖风系统",了解相关正确步骤。 请参考专门出版物, NEDG5065, "空调工具"了解正确工具信息。
End By: 安装发动机罩。 请参考 拆解和装配, "发动机罩 - 拆卸和安装"。
Caterpillar Information System:
914G and 914G2 Compact Wheel Loaders and IT14G and IT14G2 Integrated Toolcarriers Machine Systems Cab - Remove
992K Wheel Loader and 854K Wheel Dozer Braking System Pressure Sensor (Service Brake Oil)
AccuGrade Laser System CB 1 Set Limits Fault
SCJ and 8SC Series Alternators Regulator - Test
992G Wheel Loader Electrohydraulic System Lift and Tilt Cylinder Drift (VIMS) - Check
SCJ and 8SC Series Alternators Diode Assembly - Test
C15 and C18 Engines for Caterpillar Built Machines Vibration Damper - Check
992G Wheel Loader Electrohydraulic System Electrical System Schematic
525B and 535B Wheel Skidders Machine Systems Hydraulic Rotator - Install - Standard Rotation Grapple
525B and 535B Wheel Skidders Machine Systems Hydraulic Rotator - Remove - Standard Rotation Grapple
2004/05/17 Special Instruction, REHS2154, "Procedure To Replace The Enclosure Brackets On A 973C Track-Type Loader" is Now Available {7263}
C175-16 Locomotive Engine Cooling System Coolant Extender (ELC) - Add
SCJ and 8SC Series Alternators Residual Magnetism - Restore
SCJ and 8SC Series Alternators Brush Assembly - Test
SCJ and 8SC Series Alternators Brush Length - Check
C11 and C13 Engines Cylinder Head Valves
D10T Track-Type Tractor Indicators and Gauges - Test
AccuGrade Laser System CB 2 Lost Beam
AccuGrade Laser System CB 3 Calibration Failure
D3G, D4G and D5G Track-Type Tractors AccuGrade Laser CB 6 Wrong Blade Motion
AccuGrade Laser System CB 8 No Blade Movement
2004/04/19 Correction to Systems Operation Testing and Adjusting, "Control Valve (Hoist)" {5051, 5136}
Procedure To Replace The Brackets For The Enclosure On A 973C Track-Type Loader{7257, 7263} Procedure To Replace The Brackets For The Enclosure On A 973C Track-Type Loader{7257, 7263}
Product Link PL-102C{7602} Product Link PL-102C{7602}