Cab - Remove
拆卸步骤
Show/hide table
所需工具     | |||
---|---|---|---|
工具     | 零件号     | 零件描述     | 数量     |
A     | FT2943     | 隔套     | 2     |
138-7575 | 连杆支架     | 4     | |
ZZ     | 6V-9508     | 螺塞     | 13     |
6V-9829 | 盖组件     | 13     |
开始:
- 拆下发动机罩。 请参考拆解和装配, "发动机罩 - 拆卸和安装"。
- 释放液压系统压力。 请参考拆解和装配, "系统压力 - 释放"。
Show/hide table
在工作温度下,发动机冷却液是热的,并且带有压力。 蒸汽还会引起人身伤害。 只有在发动机已关闭且加注口盖冷却到可徒手触摸后,才能检查冷却液液位。 缓慢卸下加注口盖,释放其中压力。 冷却系统添加剂含碱。 应避免皮肤和眼睛与其接触,以防造成人身伤害。 |
Show/hide table
注意 |
---|
在检验、保养、测试、调整及维修产品时,务必留心,确保液体盛装在容器中。 在打开任何腔室或拆解任何储有液体的部件之前,要准备好用合适的容器收集液体。 有关适合收集和盛接卡特彼勒产品上液体的工具及用品,参考专门出版物, NENG2500, "卡特彼勒工具和修理车间设备指南"。 按照当地法规和指令处置所有液体。 |
Show/hide table
接触制冷剂会使人受伤。 接触制冷剂会造成冻伤。 让手、脸避开,有助于防止受伤。 制冷管路被打开时,即使压力计显示系统中已经没有制冷剂,也要始终戴着护目镜。 拆卸管件时,务必小心谨慎。 慢慢地拧松接头。 如果系统内仍有压力,就要把它缓慢地释放到一个通风良好的地方去。 通过燃着的香烟吸入制冷剂会使人受伤或死亡。 通过燃着的香烟或其他抽烟方法吸入空调制冷气体,或者,吸入空调制冷气体接触明火而形成的烟雾,都会造成对人体的伤害 或死亡。 维修空调时,或者,在任何可能存在制冷气体的地方都不要抽烟。 采用经过认可的回收和循环利用车妥善地从空调器中取出制冷剂。 |
注: 维修数据:拆卸和安装中的工具 (ZZ) 将不在图示中列出。 显示这一工具是为了协助有经验的维修人员。
- 回收空调制冷剂。 请参考维修手册, SENR5664, "空调和加热器 R-134a 所有 Caterpillar 机器"。
- 将冷却系统中的冷却液排放到适当的容器中。
- 断开软管组件 (1) 。
Show/hide table
图 1 | g01062571 |
- 断开软管 (2) 。
Show/hide table
图 2 | g01062572 |
- 断开软管 (3) 。
Show/hide table
图 3 | g01062574 |
- 松开螺母 (5) ,然后向内转动操纵杆 (4) 。
Show/hide table
图 4 | g01062575 |
- 拆下操纵杆 (6) 和板 (7) 。
- 拆下护线圈 (8) 。
Show/hide table
图 5 | g01062579 |
- 拆下螺钉 (9) 。 拆下盖 (10) 。
Show/hide table
图 6 | g01062582 |
Show/hide table
图 7 | g01062583 |
- 断开软管组件 (11) 。
Show/hide table
图 8 | g01062584 |
- 拆下螺栓 (12) 和防护罩组件 (13) 。
Show/hide table
图 9 | g01062586 |
- 断开线束组件 (14) 。
Show/hide table
图 10 | g01062587 |
- 断开接地母线组件 (15) 和线束组件 (16) 。
Show/hide table
图 11 | g01062588 |
- 断开线束组件 (18) 。 拆下螺栓 (17) ,然后重新安置阀组件 (19) 。
Show/hide table
图 12 | g01062589 |
- 拆下地板垫 (20) 。
Show/hide table
图 13 | g01062590 |
- 拆下螺栓 (21) ,然后重新安置计量泵 (22) 。
Show/hide table
图 14 | g01062629 |
Show/hide table
图 15 | g01062630 |
- 拆下螺钉 (23) 和盖组件 (24) 。
Show/hide table
图 16 | g01062643 |
- 拆下螺母 (25) ,然后断开电缆组件 (26) 。
Show/hide table
图 17 | g01062650 |
- 拆下螺钉 (27) 和存储箱 (28) 。
Show/hide table
图 18 | g01062651 |
- 拆下销 (29) 、卡箍 (32) 和夹子 (30) 。 重新安置电缆组件 (31) ,使其远离驾驶室。
Show/hide table
图 19 | g01064026 |
- 将工具 (A) 和适当的起吊设备安装到驾驶室 (33) 上。 驾驶室 (33) 的重量约为 862 kg (1900 lb)。
Show/hide table
图 20 | g01064113 |
- 将螺栓 (34) 从驾驶室前部拆下。
Show/hide table
图 21 | g01064115 |
- 将螺栓 (35) 从驾驶室后部拆下。
Show/hide table
图 22 | g01064187 |
- 将驾驶室从机器上拆下。 如有必要,拆下橡胶座和套筒。
Caterpillar Information System:
992K Wheel Loader and 854K Wheel Dozer Braking System Pressure Sensor (Service Brake Oil)
AccuGrade Laser System CB 1 Set Limits Fault
SCJ and 8SC Series Alternators Regulator - Test
992G Wheel Loader Electrohydraulic System Lift and Tilt Cylinder Drift (VIMS) - Check
SCJ and 8SC Series Alternators Diode Assembly - Test
C15 and C18 Engines for Caterpillar Built Machines Vibration Damper - Check
992G Wheel Loader Electrohydraulic System Electrical System Schematic
525B and 535B Wheel Skidders Machine Systems Hydraulic Rotator - Install - Standard Rotation Grapple
525B and 535B Wheel Skidders Machine Systems Hydraulic Rotator - Remove - Standard Rotation Grapple
2004/05/17 Special Instruction, REHS2154, "Procedure To Replace The Enclosure Brackets On A 973C Track-Type Loader" is Now Available {7263}
C175-16 Locomotive Engine Cooling System Coolant Extender (ELC) - Add
906 and 908 Wheel Loaders Hydraulic and Steering System Pilot Hydraulic System
914G and 914G2 Compact Wheel Loaders and IT14G and IT14G2 Integrated Toolcarriers Machine Systems Cab - Install
SCJ and 8SC Series Alternators Residual Magnetism - Restore
SCJ and 8SC Series Alternators Brush Assembly - Test
SCJ and 8SC Series Alternators Brush Length - Check
C11 and C13 Engines Cylinder Head Valves
D10T Track-Type Tractor Indicators and Gauges - Test
AccuGrade Laser System CB 2 Lost Beam
AccuGrade Laser System CB 3 Calibration Failure
D3G, D4G and D5G Track-Type Tractors AccuGrade Laser CB 6 Wrong Blade Motion
AccuGrade Laser System CB 8 No Blade Movement
2004/04/19 Correction to Systems Operation Testing and Adjusting, "Control Valve (Hoist)" {5051, 5136}
Procedure To Replace The Brackets For The Enclosure On A 973C Track-Type Loader{7257, 7263} Procedure To Replace The Brackets For The Enclosure On A 973C Track-Type Loader{7257, 7263}