Engine Oil Pump - Assemble
Show/hide table
Required Tools | |||
---|---|---|---|
Tool | Part Number | Part Description | Qty |
A | 1P-0510 | Driver Group | 1 |
Show/hide table
NOTICE |
---|
Keep all parts clean from contaminants. Contaminants may cause rapid wear and shortened component life. |
- Use Tooling (A) to install bearings (10) in body (4) until the bearings are
0.30 ± 0.25 mm (0.012 ± 0.010 inch) from the inside edge of the bearing bores. Install bearings (10) so the junctions in the bearings are 30 ± 15 degrees from the center line of the bearing bores, and toward the outlet passage. The outlet passage has a cavity between the bearing bores. - Install plunger (5), plunger ring (6), and spring (7).
- Install retainer (8) and bolts (9).
- Install shaft assemblies (11) into body (4).
- Use Tooling (A) to install bearings (12) in cover (13) until the bearings are even with the outside surface of cover. Install bearings (12) so the junctions in the bearings are 30 ± 15 degrees from the center line of the bearing bores and toward the outlet passage in the oil pump.
- Install cover (13) on body (4). Install bolts (14).
Show/hide table
Illustration 4 g01195925 - Install the key into the pump shaft. Install drive gear (3). Install washer (2) and bolt (1). Tighten bolt (1) to a torque of
55 ± 7 N·m (40 ± 5 lb ft) .
Show/hide table
Illustration 1 | g01195938 |
Show/hide table
Illustration 2 | g01146257 |
Show/hide table
Illustration 3 | g01146265 |
Show/hide table
Improper assembly of parts that are spring loaded can cause bodily injury. To prevent possible injury, follow the established assembly procedure and wear protective equipment. |
End By:
- Install the engine oil pump. Refer to Disassembly and Assembly, "Engine Oil Pump - Install".
Caterpillar Information System:
C32 Marine Engines Engine Oil Pump - Disassemble
C32 Marine Engines Engine Oil Pump - Install
C32 Marine Engines Engine Oil Pump - Remove
C4.4 and C6.6 Industrial Engines and Engines for Caterpillar Built Machines Idle Validation Switch Circuit - Test
C4.4 and C6.6 Industrial Engines and Engines for Caterpillar Built Machines E2143 Low Engine Coolant Level
C4.4 and C6.6 Industrial Engines and Engines for Caterpillar Built Machines E172 High Air Filter Restriction
C4.4 and C6.6 Industrial Engines and Engines for Caterpillar Built Machines E232 High Fuel/Water Separator Water Level
TH48-E80 Oil/Gas Transmission Pump Drive - Install
TH48-E80 Oil/Gas Transmission Pump Drive - Assemble
TH48-E80 Oil/Gas Transmission Pump Drive - Disassemble
TH48-E80 Oil/Gas Transmission Pump Drive - Remove
C27 and C32 Generator Set Engines Water Pump - Assemble
C32 Petroleum Engines Pistons and Connecting Rods - Assemble
3412 Generator Set Engines Fuel Injection Pump
3412 Generator Set Engines Fuel Injection Pump
3412 Generator Set Engines Fuel Injection Pump
3412 Generator Set Engines Fuel Injection Pump
C7 Engine for AP-1000D, AP-1055D, BG-2455D, and BG-260D Asphalt Pavers Engine Will Not Crank
TH48-E80 Oil/Gas Transmission Control Manifold - Remove
C15 Petroleum Generator Set Engines Fuel Filter Base
TH48-E80 Oil/Gas Transmission Control Manifold - Install
TH48-E80 Oil/Gas Transmission Control Manifold - Disassemble
TH48-E80 Oil/Gas Transmission Control Manifold - Assemble
C15 Petroleum Generator Set Engines Turbocharger