Engine Oil Pan - Remove and Install
Removal Procedure
Show/hide table
| Required Tools | |||
| Tool | Part Number | Part Description | Qty |
| A | 1U-7505 | Hydraulic Jack | 1 |
Show/hide table
| NOTICE |
|---|
Keep all parts clean from contaminants. Contaminants may cause rapid wear and shortened component life. |
Show/hide table
| NOTICE |
|---|
Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids. Refer to Special Publication, NENG2500, "Caterpillar Dealer Service Tool Catalog" for tools and supplies suitable to collect and contain fluids on Caterpillar products. Dispose of all fluids according to local regulations and mandates. |
- Drain the engine oil from the engine oil pan into a suitable container for storage or disposal. Refer to Operation and Maintenance Manual, "Refill Capacities".
- Remove the tube assembly from engine oil pan (3) .
Show/hide table
 | |
| Illustration 1 | g01194125 |
- If necessary, remove pipe plugs (4) from engine oil pan (3) .
- Use Tooling (A) to support engine oil pan (3). The weight of engine oil pan (3) is approximately 25 kg (55 lb).
- Remove bolts (2) .
- Remove engine oil pan (3) and gasket (1) .
Installation Procedure
Show/hide table
| Required Tools | |||
| Tool | Part Number | Part Description | Qty |
| A | 1P-7505 | Hydraulic Jack | 1 |
Show/hide table
| NOTICE |
|---|
Keep all parts clean from contaminants. Contaminants may cause rapid wear and shortened component life. |
- Place gasket (1) on engine oil pan (3) .
Show/hide table
| | |
| Illustration 2 | g01194125 |
- Use Tooling (A) to position engine oil pan (3) on the engine. The weight of engine oil pan (3) is approximately 25 kg (55 lb).
- Install bolts (2) .
- If necessary, install pipe plugs (4) on engine oil pan (3). Tighten the pipe plugs to a torque of 80 ± 10 N·m (59 ± 7 lb ft).
- Install the tube assembly on engine oil pan (3) .
- Fill the engine with engine oil to the correct level. Refer to Operation and Maintenance Manual, "Refill Capacities".
Caterpillar Information System:
TH48-E80 Petroleum Transmission Power Train Electronic Control System Position Sensor (Transmission Gear) - Check
770 and 772 Off-Highway Truck Chassis Electronic Control System Starting System
3126B Generator Set Engine Engine Pressure Sensor Open or Short Circuit - Test
TH48-E80 Petroleum Transmission Power Train Electronic Control System Diagnostic Code List
TH48-E80 Petroleum Transmission Power Train Electronic Control System Diagnostic Capabilities
C13, C15, and C18 Tier 4 Final Engines Electric Starting Motor
C4.4 and C6.6 Industrial Engines and Engines for Caterpillar Built Machines Fuel Rail Pump Solenoid - Test
TH48-E80 Petroleum Transmission Power Train Electronic Control System Electrical Component and Connector Locations
Caterpillar On-Highway Diesel Engine Fluids Recommendations Characteristics of Diesel Fuel
2005/08/15 An Improved Idler Pulley Has Been Released {1358}
3412E Petroleum Engine Crankcase Breather - Remove and Install
2005/08/01 An Improved Idler Pulley Has Been Released {1358}
3126B Generator Set Engine Engine Temperature Sensor Open or Short Circuit - Test
3412E Petroleum Engine Cylinder Liner - Install
3608 Engine Crankshaft Position for Fuel Timing and Valve Lash Adjustment
3406C Engines for Caterpillar Built Machines Engine Oil Pump
3412E Petroleum Engine Piston Cooling Jets - Remove and Install
C280 Marine Engines Metal Particle Detector
C280 Marine Engines Metal Particle Detector - Test
C9-XQ300 Rental Generator Set Wiring Diagrams
3412E Petroleum Engine Pistons and Connecting Rods - Disassemble
3512C SR4B Generator Sets Product Description
C280 Marine Engines Internal Lubrication
2005/11/21 A New Connecting Rod is Used in 3500B and 3500C High Displacement Machine Engines {1218}