Transmission Magnetic Screen - Clean
Show/hide table
 |
Hot oil and hot components can cause personal injury. Do not allow hot oil or hot components to contact the skin. |
 |
Show/hide table
| NOTICE |
|---|
Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids. Refer to Special Publication, NENG2500, "Caterpillar Tools and Shop Products Guide" for tools and supplies suitable to collect and contain fluids on Caterpillar products. Dispose of all fluids according to local regulations and mandates. |
- Park the machine on a level surface. Engage the parking brake. Stop the engine.
- Remove cover assembly (1) .
Show/hide table
 | |
| Illustration 1 | g01013191 |
Show/hide table
 | |
| Illustration 2 | g01013192 |
- Remove seal (2) .
Show/hide table
 | |
| Illustration 3 | g01013193 |
- Remove screen tube assembly (3) and suction screen (5) .
- Wash the screen tube assembly and the suction screen in clean, nonflammable solvent.
Show/hide table
 | |
| Illustration 4 | g00947579 |
Show/hide table
| NOTICE |
|---|
Do not drop or rap the magnets against any hard objects. Replace any damaged magnets. |
- Clean magnets (4) with a cloth, stiff bristle brush, or pressure air.
- Clean the cover. Inspect seal (2). Replace the seal if it is damaged.
- Install screen tube assembly (3) and suction screen (5) .
- Install seal (2) and cover assembly (1) .
- Start the engine and run the engine at low idle. Inspect for leaks.
- Maintain the transmission oil level to the "FULL" mark in sight gauge (6). Remove oil filler cap (7) and add oil, if necessary.
Show/hide table
 | |
| Illustration 5 | g01013195 |
- Stop the engine.
Caterpillar Information System:
AD55 Underground Articulated Truck Transmission Breather - Replace
994D Wheel Loader Bucket Cutting Edges - Inspect/Replace
994D Wheel Loader Battery or Battery Cable - Inspect/Replace
3500B and 3500C Marine Engines Engine Governing - Adjust
D3G, D4G and D5G Track-Type Tractors Electrohydraulic Fuse
D3G, D4G and D5G Track-Type Tractors Electrohydraulic Electrical Component and Connector Locations
D3G, D4G and D5G Track-Type Tractors Electrohydraulic Position Sensor (Steering) of Joystick Control - Calibrate
D3G, D4G and D5G Track-Type Tractors Electrohydraulic Calibration
615C Series II Wheel Tractor-Scraper Hydraulic System Vane Pump (Elevator)
3126B Machine Engines Throttle Switch Circuit - Test
Rework of the Stabilizer Link and Tilt Cylinder Lines{5057, 5104} Rework of the Stabilizer Link and Tilt Cylinder Lines{5057, 5104}
D3G, D4G and D5G Track-Type Tractors Brakes, Indicators and Gauges - Test
D3G, D4G and D5G Track-Type Tractors Electrohydraulic Position Sensor (Forward/Neutral/Reverse) of Joystick Control - Calibrate
D3G, D4G and D5G Track-Type Tractors Electrohydraulic Position Sensor (Service Brake Pedal) - Calibrate
D3G, D4G and D5G Track-Type Tractors Capacities (Refill)
2003/08/01 A Previous High Temperature Locknut is Used in Engine Exhaust System Groups {7553}
D3G, D4G and D5G Track-Type Tractors Electrohydraulic Forward Solenoids of Drive Pumps and Solenoids of Drive Motors - Calibrate
Bench Test Procedure for a 988G and 988H Wheel Loader Transmission {3030, 3073, 3139} Bench Test Procedure for a 988G and 988H Wheel Loader Transmission {3030, 3073, 3139}
D3G, D4G and D5G Track-Type Tractors Electrohydraulic Reverse Solenoids of Drive Pumps - Calibrate
D3G, D4G and D5G Track-Type Tractors Electrohydraulic Position Sensor (Deceleration Pedal) - Calibrate
2003/07/21 A New Fuel Priming Pump Is Used on the Wheel Feller Bunchers and the Wheel Skidders {1258}
AD55 Underground Articulated Truck Transmission Oil - Change
AD55 Underground Articulated Truck Transmission Oil Filter - Replace
AD55 Underground Articulated Truck Transmission Oil Level - Check