Pistons and Connecting Rods - Install
安装步骤
Show/hide table
所需工具     | |||
---|---|---|---|
工具     | 零件号     | 零件描述     | 数量     |
A     | 9S-9082     | 发动机盘车工具     | 1     |
B (1)     | 5P-3526     | 活塞环压缩器     | 1     |
B (2)     | 200-3914     | 活塞环压缩器     | 1     |
C     | 8T-3052     | 度数轮     | 1     |
Show/hide table
( 1 ) | 用于 C15 发动机。 |
( 2 ) | 用于 C18 发动机。 |
Show/hide table
注意 |
---|
保持所有零件清洁无杂质。 杂质会造成快速磨损和缩短部件寿命。 |
注: 当间隙检查完成后,安装连杆轴承,并保持干燥。 请参阅拆解与组装, "轴承间隙 – 检查"。 为了便于最终组装,在连杆轴承上涂抹清洁的发动机机油。
- 将清洁的发动机机油涂抹在缸套孔、活塞环,以及活塞外表面上。
注: 活塞和连杆与指定气缸相配。 确保将连杆和活塞安装进正确气缸中。
- 使用工具 (A) 转动曲轴直到连杆轴颈位于底部中央位置。
- 使用工具 (B) 将活塞 (3) 和连杆装进缸套。
注: 安装连杆,以使轴承凸舌位于活塞冷却喷嘴一侧。
Show/hide table
图 1 | g01048560 |
注: 在安装活塞和连杆期间,小心不要损坏缸套和曲轴轴颈。
- 将连杆轴承上轴瓦安装到连杆中。
注: 确保安装连杆轴承时使轴承凸舌卡入连杆凹槽中。
- 使用清洁的发动机机油润滑连杆轴承,并将连杆拉至曲轴轴颈上。
- 将连杆轴承的下轴瓦安装进连杆轴承盖中。
注: 确保安装连杆轴承时使轴承凸舌卡入连杆凹槽中。
- 将连杆轴承盖 (2) 安置在连杆上。
注: 确保连杆轴承盖一侧的数字和连接杆上的数字在同一侧。 连杆轴承盖及连杆上的轴承凸舌都位于活塞冷却喷嘴侧。
Show/hide table
图 2 | g01016640 |
- 使用清洁的发动机机油润滑螺栓 (1) 的螺纹并安装螺栓 (1) 。
- 按照以下步骤拧紧螺栓 (1) :
- 将螺栓 (A) 和螺栓 (C) 拧紧至扭矩为 70 ± 4 N·m (50 ± 3 lb ft)。
- 将紧螺栓 (B) 和螺栓 (D) 拧紧至扭矩为 70 ± 4 N·m (50 ± 3 lb ft)。
- 将螺栓 (B) 和 (D) 再次旋转 60 ± 5 度(1/6 圈)。
注: 如果没有使用工具 (C) ,请为每个螺栓作指示标记。
- 将螺栓 (A) 和螺栓 (C) 拧紧至扭矩为 70 ± 4 N·m (50 ± 3 lb ft)。
- 将螺栓 (A) 和 (C) 再次旋转 60 ± 5 度(1/6 圈)。
注: 如果没有使用工具 (C) ,请为每个螺栓作指示标记。
- 转动曲轴,以便确保曲轴能转动自如。
End By:
- 安装活塞冷却喷嘴。 请参阅 拆解和组装, "活塞冷却喷嘴 - 拆卸和安装"。
- 安装发动机机油泵。 请参阅 拆解和组装, "发动机机油泵 - 安装"。
- 安装缸盖。 请参阅 拆解和组装, "缸盖 - 安装"。
Caterpillar Information System:
C15 and C18 Generator Set Engines Connecting Rod Bearings - Remove
C15 On-Highway Engine Crankshaft - Install
C15 and C18 Generator Set Engines Pistons and Connecting Rods - Disassemble
C15 On-Highway Engine Pistons and Connecting Rods - Assemble
C15 On-Highway Engine Camshaft - Remove
C15 On-Highway Engine Camshaft - Install
C15 and C18 Generator Set Engines Connecting Rod Bearings - Install
C15 and C18 Generator Set Engines Crankshaft Main Bearings - Remove
C15 On-Highway Engine Crankshaft - Remove
C15 and C18 Generator Set Engines Crankshaft Main Bearings - Install
963C Track-Type Loader Track - Check/Adjust
IT62G Integrated Toolcarrier and 950G and 962G Wheel Loaders Cooling System Coolant Sample (Level 2) - Obtain
C7 Engines for Caterpillar Built Machines Camshaft Idler Gear - Remove and Install
966G Series II Wheel Loader and 972G Series II Wheel Loader Hydraulic System Tilt Cylinder - High Lift
IT62G Integrated Toolcarrier and 950G and 962G Wheel Loaders Differential and Final Drive Oil Sample - Obtain
IT62G Integrated Toolcarrier and 950G and 962G Wheel Loaders Engine Air Filter Service Indicator - Inspect/Replace
3500B Series II Marine Engines MID 036 - CID 0253 - FMI 02 Personality Module mismatch
3500B Series II Marine Engines MID 036 - CID 0254 - FMI 12 Electronic Control Module Error
Installation Instructions for the 2Q-8564 Ride Control Gp (KIT){5004, 5004} Installation Instructions for the 2Q-8564 Ride Control Gp (KIT){5004, 5004}
C7 Engines for Caterpillar Built Machines Camshaft Bearings - Remove and Install
966G Series II Wheel Loader and 972G Series II Wheel Loader Hydraulic System Relief Valve
Installation of Product Link{7602} Installation of Product Link{7602}
IT62G Integrated Toolcarrier and 950G and 962G Wheel Loaders Engine Oil Sample - Obtain
966G Series II Wheel Loader and 972G Series II Wheel Loader Hydraulic System Electrohydraulic Control