Pistons and Connecting Rods - Assemble
Show/hide table
所需工具 | |||
---|---|---|---|
工具 | 零件号 | 零件描述 | 数量 |
A | 6V-6192 | 钳子 | 1 |
B | 7M-3978(1)
7B-7974(2) |
活塞环扩张器总成 | 1 |
C | 5P-8639 | 液压压力 (连杆轴承) | 1 |
8F-0024 | 软管组件 | 1 | |
1P-2375 | 连接器 | 1 | |
1P-2376 | 连接器 | 1 | |
5P-8651 | 隔套 | 1 | |
5P-8649 | 齿座 | 1 | |
5P-8650 | 衬套接头 | 1 | |
9U-6600 | 液压泵 | 1 |
Show/hide table
(1) | C15 |
(2) | C18 |
注: 从发动机上拆下之前,活塞和连杆组件上已经做了标记。 所有的部件必须重新组装在一起。 所有部件必须安装回它们在发动机中原来的位置。 请勿互换任何部件。
Show/hide table
注意 |
---|
保持所有零件清洁无杂质。 杂质会造成快速磨损和缩短部件寿命。 |
- 使用工具 (C) 拆掉旧轴承,同时安装新轴承 (7)。 工具 (C) 的适配器应与连杆 (6) 的表面充分接触。
注: 将轴承接头的方位调整到 (X) 位置的 ± 5 度范围内。
- 沿长度 (Y) 加热连杆 (6)。
(Y) 加热连杆的最大长度 ...
93 mm (3.7 inch) - 让连杆和轴承冷却到室温。
Show/hide table注意 在安装活塞销子轴承的时候,必须对连杆进行加热处理。 不要使用明火加热。
- 沿长度 (Y) 加热连杆 (6)。
- 用销膛磨机加工轴承孔 (7),以修正直径。
轴承孔直径 ...
60.035 ± 0.008 mm (2.3636 ± 0.0003 inch) Show/hide table图 3 g01017728 - 将控油环的弹簧放置在活塞体组件中的油环槽中。
- 将控油环 (3) 安置在弹簧的上方。 放置控油环,使其开口与弹簧接头成 180 度。 使用工具 (B) 将控油环安装在活塞上。
- 使用工具 (B) 安装中间活塞环 (2),使有 “UP-2” 标记的一侧朝向活塞顶部。
- 使用工具 (B) 安装顶部活塞环 (1),使有 “UP-1” 标记的一侧朝向活塞顶部。
- 安置活塞环 (1)、 (2) 和 (3),使其开口之间互成120度。
- 检查活塞环 (1)、 (2) 和 (3) 底部之间的间隙。 关于技术规格,请参阅技术规格手册, "活塞和活塞环"。
- 将活塞体组件 (4) 在连杆 (6) 上安置到位。 将清洁的发动机机油涂抹在连杆销 (8) 上,并安装连杆销 (8)。 使用工具 (A) 安装销固定器 (5)。 确保销固定器 (5) 完全落座在活塞体组件 (4) 的槽中,
- 将连杆轴承 (9) 安装在连杆 (6) 和连杆盖 (10) 上。 确保安装连杆轴承 (9) 时轴承凸舌卡入连杆 (6) 和连杆盖 (10) 中的凹槽。
- 确保定位销已安装到连杆盖 (10) 中。
Show/hide table
图 1 | g01018268 |
Show/hide table
图 2 | g01017742 |
结束:
- 安装活塞和连杆。 请参阅拆解和组装, "活塞和连杆 - 安装"。
Caterpillar Information System:
C15 On-Highway Engine Camshaft - Remove
C15 On-Highway Engine Camshaft - Install
C15 and C18 Generator Set Engines Connecting Rod Bearings - Install
C15 and C18 Generator Set Engines Crankshaft Main Bearings - Remove
C15 On-Highway Engine Crankshaft - Remove
C15 and C18 Generator Set Engines Crankshaft Main Bearings - Install
963C Track-Type Loader Track - Check/Adjust
IT62G Integrated Toolcarrier and 950G and 962G Wheel Loaders Cooling System Coolant Sample (Level 2) - Obtain
IT62G Integrated Toolcarrier and 950G and 962G Wheel Loaders Cooling System Coolant Sample (Level 1) - Obtain
2003/03/31 Correction to Disassembly and Assembly , "Bucket" {6101}
IT62G Integrated Toolcarrier and 950G and 962G Wheel Loaders Daily Inspection
AD30 Underground Articulated Truck Engine Air Filter Secondary Element - Replace
C15 and C18 Generator Set Engines Pistons and Connecting Rods - Disassemble
C15 On-Highway Engine Crankshaft - Install
C15 and C18 Generator Set Engines Connecting Rod Bearings - Remove
C15 and C18 Generator Set Engines Pistons and Connecting Rods - Install
C7 Engines for Caterpillar Built Machines Camshaft Idler Gear - Remove and Install
966G Series II Wheel Loader and 972G Series II Wheel Loader Hydraulic System Tilt Cylinder - High Lift
IT62G Integrated Toolcarrier and 950G and 962G Wheel Loaders Differential and Final Drive Oil Sample - Obtain
IT62G Integrated Toolcarrier and 950G and 962G Wheel Loaders Engine Air Filter Service Indicator - Inspect/Replace
3500B Series II Marine Engines MID 036 - CID 0253 - FMI 02 Personality Module mismatch
3500B Series II Marine Engines MID 036 - CID 0254 - FMI 12 Electronic Control Module Error
Installation Instructions for the 2Q-8564 Ride Control Gp (KIT){5004, 5004} Installation Instructions for the 2Q-8564 Ride Control Gp (KIT){5004, 5004}
C7 Engines for Caterpillar Built Machines Camshaft Bearings - Remove and Install