Connecting Rod Bearings - Install
Show/hide table
需要的工具 | |||
---|---|---|---|
工具 | 零件号 | 零件名称 | 数量 |
A | 9S-9082 | 发动机盘车工具 | 1 |
B | 8T-3052 | 度数轮 | 1 |
Show/hide table
注意 |
---|
保持所有零件清洁无杂质。 杂质会造成快速磨损和缩短部件寿命。 |
- 使用工具 (A)转动曲轴,直到连杆轴颈位于底部中央。
- 在连杆轴承盖 (2)里安装一个新的连杆轴承 (3)下半部分。
注: 确保轴承锁舌 (4)位于连杆轴承盖的凹槽中。
- 将新的连杆轴承上轴瓦安装到连杆中。
注: 确保轴承锁舌位于连接杆的凹槽中。
- 把连杆拉到曲轴上。
Show/hide table
图 2 g01016640 - 将连杆轴承盖 (2) 安置在连杆上。
注: 确保连杆轴承盖一侧的数字和连接杆上的数字在同一侧。 连杆轴承盖及连杆上的轴承凸舌都位于活塞冷却喷嘴侧。
- 用干净的发动机机油润滑螺栓 (1)的螺纹。 安装螺栓。
- 按照以下的方法拧紧螺栓 (1):
- 拧紧螺栓 (A) 和螺栓 (C) 至扭矩为
70 ± 4 N·m (52 ± 3 lb ft) 。 - 拧紧螺栓 (B) 和螺栓 (D) 至扭矩为
70 ± 4 N·m (52 ± 3 lb ft) 。 - 把螺栓 (B)和 (D)再次旋转60 ± 5度( 1/6 圈)。
注: 如果没有使用工具 (B),应在每个螺栓上加索引标记。
- 再拧紧螺栓 (A) 和螺栓 (C) 至扭矩为
70 ± 4 N·m (52 ± 3 lb ft) 。 - 再拧紧螺栓 (A) 和螺栓 (C) 60 ± 5 度(1/6 圈)。
注: 如果没有使用工具 (B),应在每个螺栓上加索引标记。
- 转动曲轴,以便确保曲轴能转动自如。
- 拧紧螺栓 (A) 和螺栓 (C) 至扭矩为
注: 当间隙检查完成后,安装连杆轴承,并保持干燥。 请参阅拆解和组装, "轴承间隙 - 检查"。 为了便于最终组装,在连杆轴承上涂敷清洁的发动机机油。
Show/hide table
图 1 | g00998730 |
结束:
- 安装发动机机油泵。 请参阅拆解和组装, "发动机机油泵 - 安装"。
Caterpillar Information System:
C15 and C18 Generator Set Engines Crankshaft Main Bearings - Remove
C15 On-Highway Engine Crankshaft - Remove
C15 and C18 Generator Set Engines Crankshaft Main Bearings - Install
963C Track-Type Loader Track - Check/Adjust
IT62G Integrated Toolcarrier and 950G and 962G Wheel Loaders Cooling System Coolant Sample (Level 2) - Obtain
IT62G Integrated Toolcarrier and 950G and 962G Wheel Loaders Cooling System Coolant Sample (Level 1) - Obtain
2003/03/31 Correction to Disassembly and Assembly , "Bucket" {6101}
IT62G Integrated Toolcarrier and 950G and 962G Wheel Loaders Daily Inspection
AD30 Underground Articulated Truck Engine Air Filter Secondary Element - Replace
AD30 Underground Articulated Truck Screen (Torque Converter) - Clean
AD30 Underground Articulated Truck Tire Inflation - Check
AD30 Underground Articulated Truck Steering Cylinder Bearings - Lubricate
C15 On-Highway Engine Camshaft - Install
C15 On-Highway Engine Camshaft - Remove
C15 On-Highway Engine Pistons and Connecting Rods - Assemble
C15 and C18 Generator Set Engines Pistons and Connecting Rods - Disassemble
C15 On-Highway Engine Crankshaft - Install
C15 and C18 Generator Set Engines Connecting Rod Bearings - Remove
C15 and C18 Generator Set Engines Pistons and Connecting Rods - Install
C7 Engines for Caterpillar Built Machines Camshaft Idler Gear - Remove and Install
966G Series II Wheel Loader and 972G Series II Wheel Loader Hydraulic System Tilt Cylinder - High Lift
IT62G Integrated Toolcarrier and 950G and 962G Wheel Loaders Differential and Final Drive Oil Sample - Obtain
IT62G Integrated Toolcarrier and 950G and 962G Wheel Loaders Engine Air Filter Service Indicator - Inspect/Replace
3500B Series II Marine Engines MID 036 - CID 0253 - FMI 02 Personality Module mismatch