Connector Locations
Show/hide table
Illustration 1 | g01037606 |
ECM connectors for ADEM II and ADEM III |
Show/hide table
Illustration 2 | g00932167 |
Control Station Processor (CSP) (1) Connector for the "port throttle/gear" (2) Connector for the "stbd throttle/gear" (3) Connector for the "switch panel" (4) Connector for the power train control processor ("PCP") |
Show/hide table
Illustration 3 | g00932310 |
Power Train Control Processor (PCP) (5) Connector for the backup station (6) Connector for the master station (7) Connector for power (8) Connector for the control station (9) Connector for the port transmission (10) Connector for the port "ECM/ETP" (11) Connector for the starboard "ECM/ETP" (12) Connector for the starboard transmission |
Show/hide table
Connector Pinouts for the Backup Station (5)
on the Power Train Control Processor (PCP) |
|
Pin | Description |
1 | +Power |
2 | -Power |
3 | +CAN link |
4 | -CAN link |
5 | CAN shield |
6 | -CAN term loop |
7 | +CAN term loop |
8 | Reserved |
Show/hide table
Connector Pinouts for the Master Station (6) and the Control Station (8)
on the Power Train Control Processor (PCP) |
|
Pin | Description |
1 | +Power |
2 | -Power |
3 | +CAN link |
4 | -CAN link |
5 | CAN shield |
6 | -CAN term loop |
7 | +CAN term loop |
8 | Station Lockout Input |
Show/hide table
Connector Pinouts for Power Connector (7) of the Power Train Control Processor (PCP) | |
Pin | Description |
1 | Port ignition |
2 | Select return |
3 | Starboard ignition |
4 | System voltage select jumper |
5 | External alarm common |
6 | External alarm NC |
7 | -Battery 1 (sec) |
8 | +Battery 1 (primary) |
9 | +Battery 1 (primary) |
10 | +Battery 1 (secondary) |
11 | +Battery 1 (secondary) |
12 | -Battery |
Show/hide table
Connector Pinouts for the Port Transmission (9) and the Starboard Transmission (12 ) of the Power Train Control Processor (PCP) | |
Pin | Description |
1 | +V FWD |
2 | -V CMD |
3 | +V CMD |
4 | +V REV |
5 | -V REV |
6 | Status return |
7 | Status input |
8 | -V FWD |
Show/hide table
Connector Pinouts for the Port ECM/ETP (10) and Starboard ECM/ETP (11) of the Power Train Control Processor (PCP) | |
Pin | Description |
1 | +J1939 link |
2 | -J1939 link |
3 | Troll enable |
4 | Ground ECM |
5 | Primary PWM |
6 | Secondary throttle select |
7 | Secondary PWM |
8 | Slow vessel mode (SVM) |
9 | Reserved |
10 | Reserved |
11 | Reserved |
12 | J1939 shield |
Caterpillar Information System:
Marine Multi-Station Control System Electronic Service Tool Will Not Communicate with PCP
Marine Multi-Station Control System Diagnostic Code List
Marine Multi-Station Control System Engine Cranks but Will Not Start
Marine Multi-Station Control System Using Caterpillar Electronic Technician (ET) to Determine Diagnostic Codes
Marine Multi-Station Control System ECM CID 0091 - FMI 08
Marine Multi-Station Control System ECM CID 0091 - FMI 13
Marine Multi-Station Control System ECM CID 0116 - FMI 00
Marine Multi-Station Control System ECM CID 0168 - FMI 00
Marine Multi-Station Control System ECM CID 0168 - FMI 01
Marine Multi-Station Control System ECM CID 0168 - FMI 02
3126B Petroleum Engine Belt Tightener - Remove
793D Off-Highway Truck/Tractor Accumulator (Steering) - Assemble
Marine Multi-Station Control System Service Tools
Marine Multi-Station Control System General Information
3126B Petroleum Engine Belt Tightener - Install
Marine Multi-Station Control System Marine Power Display
Marine Multi-Station Control System General Information
Marine Multi-Station Control System Control Head - Calibrate
Marine Multi-Station Control System E881 Multiple Stations on Master Control Data Link
Marine Multi-Station Control System Junction Box
C7.1 (Mech) Industrial Engine Engine Oil Cooler
C4.4 and C6.6 Industrial Engines and Engines for Caterpillar Built Machines Engine Temperature Sensor Open or Short Circuit - Test
3126B Petroleum Engine Atmospheric Pressure Sensor - Remove and Install
345C MHPU Mobile Hydraulic Power Unit Machine Systems Swing Motor - Disassemble