Diagnostic Code List
Use the Caterpillar Electronic Technician (Cat ET) in order to determine the diagnostic codes for the PCP or the ECM. After determining the diagnostic codes, refer to the corresponding test procedure for more information. Perform the procedure that corresponds to the Component Identifier (CID) and the Failure Mode Identifier (FMI) of the diagnostic code. The following table is a list of possible diagnostic codes for the PCP and the ECM in the multi-station control system.
Show/hide table
Diagnostic Codes
For troubleshooting, see the procedure with the same CID and FMI. |
|
Diagnostic Codes for the Engine ECM | |
CID 0168 Electrical System | |
FMI 00 | "Voltage above normal" |
FMI 01 | "Voltage below normal" |
FMI 02 | "Battery Voltage Intermittent" |
Diagnostic Codes for the PCP | |
CID 0369 Transmission Gear Indicator Input | |
FMI 07 | "Gear Not Qualified" |
CID 0700 Transmission Gear Sensor | |
FMI 02 | "Gear Signal Abnormal" |
CID 0718 Transmission System | |
FMI 02 | "XMSN Not Responding" |
CID 1326 ECM Location Code | |
FMI 09 | "ECM Not Responding" |
CID 1440 Throttle Actuator | |
FMI 02 | |
FMI 03 | "Throttle open/short to +Battery" |
FMI 04 | "Throttle Short to Ground" |
FMI 07 | "Throttle Not Qualified" |
FMI 08 | "Throttle Signal Abnormal" |
CID 1815 Marine Power Train Control Module (PCP) | |
FMI 04 | PCP Voltage Below Normal |
FMI 11 | "Backup Station Active" |
FMI 12 | "PCP Fault" |
FMI 13 | "PCP Calibration Failure" |
CID 1816 Multi-Station Control Module | |
FMI 09 | "Active Control Station Communication Loss" |
CID 1817 Total Mode Control Module | |
FMI 09 | "Troll Communications Loss" |
FMI 12 | "ETP Fault" |
CID 1821 Master Control Station Data Link | |
FMI 09 | "Master Control Station Data Link Failure" |
CID 1822 Control Station Data Link | |
FMI 09 | "Control Station Data Link Failure" |
EID | |
881 | "Multiple Control Stations on Master Control Station Data Link" |
Caterpillar Information System:
Marine Multi-Station Control System Engine Cranks but Will Not Start
Marine Multi-Station Control System Using Caterpillar Electronic Technician (ET) to Determine Diagnostic Codes
Marine Multi-Station Control System ECM CID 0091 - FMI 08
Marine Multi-Station Control System ECM CID 0091 - FMI 13
Marine Multi-Station Control System ECM CID 0116 - FMI 00
Marine Multi-Station Control System ECM CID 0168 - FMI 00
Marine Multi-Station Control System ECM CID 0168 - FMI 01
Marine Multi-Station Control System ECM CID 0168 - FMI 02
3126B Petroleum Engine Belt Tightener - Remove
793D Off-Highway Truck/Tractor Accumulator (Steering) - Assemble
793D Off-Highway Truck/Tractor Accumulator (Steering) - Disassemble
C6.6 Generator Set CID 0006 FMI 02
Marine Multi-Station Control System Electronic Service Tool Will Not Communicate with PCP
Marine Multi-Station Control System Connector Locations
Marine Multi-Station Control System Service Tools
Marine Multi-Station Control System General Information
3126B Petroleum Engine Belt Tightener - Install
Marine Multi-Station Control System Marine Power Display
Marine Multi-Station Control System General Information
Marine Multi-Station Control System Control Head - Calibrate
Marine Multi-Station Control System E881 Multiple Stations on Master Control Data Link
Marine Multi-Station Control System Junction Box
C7.1 (Mech) Industrial Engine Engine Oil Cooler
C4.4 and C6.6 Industrial Engines and Engines for Caterpillar Built Machines Engine Temperature Sensor Open or Short Circuit - Test