C15 Petroleum Generator Set Engines Caterpillar


Electric Starting Motor

Usage:

C15 115


图 1g02563097

表 1
207-1564 电起动马达总成的技术规格 
项目  数量  零件  技术规格说明 
小齿轮和壳体之间的间隙为 9.1 mm (0.36 in)。 
6V-8188 螺母  拧紧至扭矩为 30.5 ± 3.5 N·m (270 ± 31 lb in)。 
250-8279 电磁阀套件  20V 和 25 °C (77 °F) 下的耗电量:
1. 对于吸合电流为 57 安培
2. 对于保持电流为最大 16 安培 
6V-8188 螺母  拧紧至扭矩为 30.5 ± 3.5 N·m (270 ± 31 lb in)。 
6V-8378 螺母  拧紧至扭矩为 2.25 ± 0.25 N·m (20 ± 2 lb in)。 
6V-8188 螺母  蓄电池端子螺母(5)最多可使用三个电缆或导线端子。 两个端子最高不低于 0 AWG。
拧紧至扭矩为 30.5 ± 3.5 N·m (270 ± 30 lb in)。 
6V-8378 螺母  拧紧至扭矩为 2.25 ± 0.25 N·m (20 ± 2 lb in)。 
拧紧至扭矩为 8 ± 3 N·m (71 ± 27 lb in)。 
当从小齿轮端观看电起动马达时,马达顺时针旋转。
25 °C (77 °F) 时无负载
1. 转速为 7643 ± 1683 rpm
2. 电流消耗为 76.5 ± 14.5 安培
3. 电压为 23 V 

Caterpillar Information System:

938G Wheel Loader, 938G Series II Wheel Loader, IT38G Integrated Toolcarrier and IT38G Series II Integrated Toolcarrier Traction Control System Test/Enable Switch
631G and 637G Wheel Tractor-Scrapers Hydraulic System Apron
2002/10/28 Examine Failed Starting Motors to Understand the Reason for Failure {1453}
631G and 637G Wheel Tractor-Scrapers Hydraulic System Apron
2002/10/28 Correction to Operation and Maintenance Manual , "Equipment Lowering with Engine Stopped" {7000}
Bench Test Procedure for Hydraulic Piston Pumps {4268, 4306, 5070} Bench Test Procedure for Hydraulic Piston Pumps {4268, 4306, 5070}
2002/10/28 New Friction Disc Improves The Service Life Of The Drive Shaft Group Components {3253}
637G Wheel Tractor-Scraper Wheel Scraper Power Train Radiator Module
D10R Track-Type Tractor Bulldozer - Lubricate
Test Sequence for Capsule Type Fuel Nozzles{0782} Test Sequence for Capsule Type Fuel Nozzles{0782}
3054E Industrial Engine Camshaft Bearings - Remove and Install
D10R Track-Type Tractor Alternator and Fan Belts - Inspect/Adjust/Replace
2002/10/28 Correction to Operation and Maintenance Manual , "Equipment Lowering with Engine Stopped" {7000}
631G and 637G Wheel Tractor-Scrapers Machine Systems Bail Cylinder and Mounting
3126B Machine Engines 5 Volt Engine Pressure Sensor Supply Circuit - Test
D10R Main Frame and Fender Crossbeam Pinned Mount Conversion{7050} D10R Main Frame and Fender Crossbeam Pinned Mount Conversion{7050}
D10R Track-Type Tractor Safety Messages
631G and 637G Wheel Tractor-Scrapers Hydraulic System Bail Cylinder
3054E Industrial Engine Flywheel - Remove
D10R Track-Type Tractor Cooling System Extended Life Coolant Extender - Add
D11R Track-Type Tractor Model Specific Coolant Information
3516B Engine for Caterpillar Built Machines MID 036 - CID 0543 - FMI 02 Filtered Oil Pressure Sensor misinstalled
3516B Engine for Caterpillar Built Machines MID 036 - CID 0543 - FMI 03 Filtered Oil Pressure Sensor shorted high
3516B Engine for Caterpillar Built Machines MID 036 - CID 0543 - FMI 04 Filtered Oil Pressure Sensor shorted low
Back to top
The names Caterpillar, John Deere, JD, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
CH-Part.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only.