Fuel Filter Base - Remove and Install
Show/hide table
所需工具 | |||
工具 | 零件号 | 零件描述 | 数量 |
A | 185-3630 | 带式扳手总成 | 1 |
Show/hide table
注意 |
---|
保持所有零件清洁无杂质。 杂质会造成快速磨损和缩短部件寿命。 |
Show/hide table
注意 |
---|
在进行检验、保养、测试、调整及维修产品期间,必须小心以确保装好排放出的油液。 在打开任何舱室或解体任何储有液体的部件之前,要准备好合适的容器收集液体。 有关收集和盛接 Cat 产品上油液的适用工具和用品,请参阅专门出版物, NENG2500, "代理商维修工具目录"。 按照当地法规和要求处置所有液体。 |
- 使用工具 (A) 拆下燃油喷油器 (2)。
- 从燃油滤清器座 (1) 上断开软管组件 (4) 和 (5)。 立即盖住或塞住所有孔口,以防受到污染。
- 将燃油传感器 (3) 从燃油滤清器座 (1) 上断开。
- 将螺栓 (6) 和垫圈从燃油滤清器座 (1) 上拆下。 从支架上拆下燃油滤清器座 (1)。
Show/hide table
图 1 | g01167050 |
Show/hide table
图 2 | g01270505 |
- 将燃油滤清器座 (1) 放置在支架上。 安装螺栓 (6) 和垫圈。
- 将软管组件 (4) 和 (5) 连接至燃油滤清器座 (1) 上。
- 将燃油传感器 (3) 连接到燃油滤清器座上。
- 安装燃油滤清器 (2)。 请参阅操作和保养手册, "燃油系统细滤器 - 更换"一节,了解更多信息。
- 向燃油系统充油。 请参阅操作和保养手册, "燃油系统 - 充油"一节,了解更多信息。
Show/hide table
图 3 | g01270505 |
Show/hide table
图 4 | g01270530 |
Caterpillar Information System:
C7 On-highway Engine Cooling System
3500B and 3500C Generator Set Engines MID 036 - CID 0175 - FMI 03 Engine Oil Temperature open/short to +batt
3500B and 3500C Generator Set Engines MID 036 - CID 0799 - FMI 12 Need Service tool update
3500B and 3500C Generator Set Engines MID 036 - CID 0175 - FMI 04 Engine Oil Temperature short to ground
C4.4 Marine Generator Set Engines Electric Starting Motor - Remove and Install
C4.4 Marine Generator Set Engines Electric Starting Motor - Remove and Install
C4.4 Marine Generator Set Engines Fuel Filter Base - Remove and Install
C4.4 Marine Generator Set Engines Speed/Timing Sensor - Remove and Install
C9 Engine for Caterpillar Built Machines Fuel Priming Pump - Remove and Install
3500B and 3500C Generator Set Engines Diagnostic Codes
C4.4 Marine Generator Set Engines Idler Gear (Front) - Install
C4.4 Marine Generator Set Engines Expansion Tank - Remove and Install
Yellowmark Noise and Roading Homologation Statement {1062} Yellowmark Noise and Roading Homologation Statement {1062}
C9.3 Tier 4 Final Engines Water Pump - Test
2005/05/16 New 3500 Marine Propulsion Software Available {7620}
C4.4 Marine Generator Set Engines Aftercooler - Remove and Install
C280 Marine Auxiliary Engines Too Much Vibration
2005/05/01 New Full Load Settings and New Full Torque Settings are Now Available {7620}
C9.3 Tier 4 Final Engines Finding Top Center Position for No. 1 Piston
C27 and C32 Industrial and Petroleum Engines Coolant Level Sensor Circuit - Test
C7 On-highway Engine Turbocharger - Inspect
3500B and 3500C Generator Set Engines Electrical Connectors and Functions
2005/05/16 A New Aftercooler Core is Used {1063, 1064}
C9.3 Engines for Caterpillar Built Machines Vibration Damper - Check