Flywheel Housing - Inspect
Show/hide table
所需工具 | ||
---|---|---|
零件号 | 零件名称 | 数量 |
8T-5096 | 千分表总成 | 1 |
Show/hide table
图 1 | g00285931 |
检查飞轮壳体的端面跳动 |
如果使用任何其他与下述不同的测量方法,切记必须消除轴承间隙以便获取正确测量值。
- 将千分表固定在飞轮上,使千分表的测头接触飞轮壳体的端面。
- 在每一点读取千分表的读数之前,向曲轴施加一个朝向后端的力。
Show/hide table
图 2 g00285932 检查飞轮壳体的端面跳动 - 当千分表在位置 (A) 设在
0.0 mm (0.00 inch) 处时,转动飞轮。 在位置 (B)、 (C) 和 (D) 读取千分表的读数。 - 在所有四点测得的高低值间的差值不得超过
0.38 mm (0.015 inch) ,此数值就是飞轮壳体的最大许可端面跳动(轴向偏心度)。
- 将千分表固定在飞轮上,使千分表的测头接触飞轮壳体的镗孔。
Show/hide table
图 4 g00285936 - 当千分表在位置 (C) 处时,调整千分表至
0.0 mm (0.00 inch) 。 将曲轴向上推到顶住轴承的上端。 请参阅插图 4。 把测定的曲轴间隙测量值填入表中第 1 行的 (C) 列内。注: 填写千分表测量值时要写上正确的正负符号。 该符号对于表中数值的正确计算是很必要的。
- 将步骤 2 的测量值除以 2。 把得出的结果填入表中第 1 行 (B) 和 (D) 列。
- 转动飞轮,使千分表处于 (A) 位置。 将千分表调至
0.0 mm (0.00 inch) 。Show/hide table图 5 g00285932 检查飞轮壳体的镗孔跳动 - 逆时针转动飞轮,使千分表处于 (B) 位置。 将测量值填入表中。
- 逆时针转动飞轮,使千分表处于 (C) 位置。 将测量值填入表中。
- 逆时针转动飞轮,使千分表处于 (D) 位置。 将测量值填入表中。
- 将每一列中的行相加。
- 用 B 列和 D 列内的较大数值减去较小数值。 将该差值填入第 III 行。 此结果即为水平偏心度(失圆度)。 第 III 行的 C 列的数值即为垂直偏心度。
Show/hide table
图 6 g00286046 总偏心度曲线图
(1) 总垂直偏心度
(2) 总水平偏心度
(3) 可接受值
(4) 不可接受值 - 在总偏心度图上,找出垂直偏心度和水平偏心度两条线的交叉点。
- 如果交叉点处于标记为“合格”的区域内,则镗孔是对准的。 如果交叉点处于标记为“不合格”的区域内,则必须更换飞轮壳。
Show/hide table
图 3 | g00285934 |
检查飞轮壳体的镗孔跳动 |
Caterpillar Information System:
D8R Series II Track-Type Tractor Window Wiper and Washer Control
D8R Series II Track-Type Tractor Power Train Steering Differential and Brake - Disassemble
621G, 623G, 627G, 631G and 637G Wheel Tractor-Scrapers Caterpillar Monitoring System Normal Mode
627G and 637G Wheel Tractor-Scrapers Power Train Electronic Control System MID 031 - CID 0967 - FMI 09
627G and 637G Wheel Tractor-Scrapers Power Train Electronic Control System MID 031 - CID 0967 - FMI 02
627G and 637G Wheel Tractor-Scrapers Power Train Electronic Control System MID 031 - CID 0708 - FMI 06
627G and 637G Wheel Tractor-Scrapers Power Train Electronic Control System MID 031 - CID 0708 - FMI 05
627G and 637G Wheel Tractor-Scrapers Power Train Electronic Control System MID 031 - CID 0708 - FMI 03
627G and 637G Wheel Tractor-Scrapers Power Train Electronic Control System MID 031 - CID 0707 - FMI 06
3406E and 3456 Engines for Caterpillar Built Machines Cylinder Head Valves
988G Wheel Loader Power Train Power Train Guard (Transmission) - Remove and Install
938G Wheel Loader and IT38G Integrated Toolcarrier Engine Supplement Electric Starting Motor - Remove and Install
D8R Series II Track-Type Tractor Power Train Steering Differential and Brake - Assemble
D5N Track-Type Tractor Plate Locations and Film Locations
966F Series II Wheel Loader Power Train Torque Converter
627G and 637G Wheel Tractor-Scrapers Power Train Electronic Control System MID 031 - CID 1323 - FMI 03
627G and 637G Wheel Tractor-Scrapers Power Train Electronic Control System MID 031 - CID 1323 - FMI 05
627G and 637G Wheel Tractor-Scrapers Power Train Electronic Control System MID 031 - CID 1323 - FMI 06
3406E and 3456 Engines for Caterpillar Built Machines Camshaft
627G and 637G Wheel Tractor-Scrapers Power Train Electronic Control System MID 031 - CID 1326 - FMI 02
3406E and 3456 Engines for Caterpillar Built Machines Engine Oil Filter Base
966F Series II Wheel Loader Power Train Torque Converter and Pump Drive Housing
621G and 627G Wheel Tractor-Scrapers Hydraulic System Pilot Control Actuator (Bowl)
621G and 627G Wheel Tractor-Scrapers Hydraulic System Pilot Control Actuator (Ejector)