Electric Starting Motor - Remove and Install
Removal Procedure
Start By:
- Connect the steering frame lock. Refer to Disassembly and Assembly, "Steering Frame Lock - Separate and Connect".
Show/hide table
Accidental machine starting can cause injury or death to personnel working on the machine. To avoid accidental machine starting, turn the battery disconnect switch to the OFF position and remove the key. If the machine is not equipped with a battery disconnect switch, disconnect the battery cables from the battery and tape the battery clamps. Place a do not operate tag at the battery disconnect switch location to inform personnel that the machine is being worked on. |
- Open the hood.
Note: Put identification marks on all wires for installation purposes.
- Disconnect wires (1) and (2) from the starter.
Show/hide table
Illustration 1 | g00753314 |
- Remove nut (3). Remove cover (4) from the starter.
Show/hide table
Illustration 2 | g00753318 |
- Disconnect wire assembly (5) from the starter.
Show/hide table
Illustration 3 | g00753320 |
- Install a suitable lifting sling and a hoist on electric starting motor (7). Remove bolts (6) and the washers. Remove the electric starting motor. The weight of the electric starting motor is 25 kg (55 lb).
Show/hide table
Illustration 4 | g00753322 |
- If necessary, replace the gasket on the electric starting motor.
Installation Procedure
- If necessary, replace the gasket on the electric starting motor.
- Use a suitable lifting sling and a hoist to install electric starting motor (7). Remove the electric starting motor. The weight of the electric starting motor is 25 kg (55 lb). Install bolts (6) and the washers.
Show/hide table
Illustration 5 | g00753322 |
- Connect wire assembly (5) to the starter. The torque for the switch terminal nut is 2.25 ± .25 N·m (20 ± 2 lb in).
Show/hide table
Illustration 6 | g00753320 |
- Install cover (4) on the starter. Install nut (3) .
Show/hide table
Illustration 7 | g00753318 |
- Connect wires (1) and (2) to the starter. The torque for the ground terminal nut and the battery terminal nut is 30.5 ± 3.5 N·m (23 ± 3 lb ft).
Show/hide table
Illustration 8 | g00753314 |
- Close the hood.
End By: Separate the steering frame lock. Refer to Disassembly and Assembly, "Steering Frame Lock - Separate and Connect".
Caterpillar Information System:
D8R Series II Track-Type Tractor Power Train Final Drive, Steering Differential, and Brake (Left Side) - Install
3406E Engines for Caterpillar Built Machines Coolant Flow Switch Circuit - Test
3003, 3013, 3014 and 3024 Engines for Caterpillar Built Machines Cylinder Head
627G and 637G Wheel Tractor-Scrapers Power Train Electronic Control System MID 031 - CID 0707 - FMI 05
D8R Series II Track-Type Tractor Power Train Final Drive, Steering Differential, and Brake (Left Side) - Remove
627G and 637G Wheel Tractor-Scrapers Power Train Electronic Control System MID 031 - CID 0707 - FMI 03
D8R Series II Track-Type Tractor Power Train Steering Planetary and Brake - Assemble
938G Wheel Loader and IT38G Integrated Toolcarrier Engine Supplement Alternator - Remove and Install
953C Track-Type Loader Plate Locations and Film Locations
621G, 623G, 627G, 631G and 637G Wheel Tractor-Scrapers Caterpillar Monitoring System Modes Of Operation
D8R Series II Track-Type Tractor Power Train Steering Planetary and Brake - Disassemble
D8R Series II Track-Type Tractor Power Train Final Drive, Steering Planetary, and Brake (Right Side) - Install
988G Wheel Loader Power Train Power Train Guard (Transmission) - Remove and Install
3406E and 3456 Engines for Caterpillar Built Machines Cylinder Head Valves
627G and 637G Wheel Tractor-Scrapers Power Train Electronic Control System MID 031 - CID 0707 - FMI 06
627G and 637G Wheel Tractor-Scrapers Power Train Electronic Control System MID 031 - CID 0708 - FMI 03
627G and 637G Wheel Tractor-Scrapers Power Train Electronic Control System MID 031 - CID 0708 - FMI 05
627G and 637G Wheel Tractor-Scrapers Power Train Electronic Control System MID 031 - CID 0708 - FMI 06
627G and 637G Wheel Tractor-Scrapers Power Train Electronic Control System MID 031 - CID 0967 - FMI 02
627G and 637G Wheel Tractor-Scrapers Power Train Electronic Control System MID 031 - CID 0967 - FMI 09
621G, 623G, 627G, 631G and 637G Wheel Tractor-Scrapers Caterpillar Monitoring System Normal Mode
D8R Series II Track-Type Tractor Power Train Steering Differential and Brake - Disassemble
D8R Series II Track-Type Tractor Window Wiper and Washer Control
G3304 and G3306 Engines Flywheel Housing - Inspect