Steering Control Valve - Remove
拆卸步骤
Show/hide table
所需工具     | |||
---|---|---|---|
工具     | 零件号     | 零件描述     | 数量     |
A     | 138-7575     | 连杆支架     | 1     |
开始:
- 拆卸驾驶室。 请参考拆解和组装, "驾驶室 - 拆卸"。
Show/hide table
注意 |
---|
在检验、保养、测试、调整及维修产品时,务必留心,确保液体盛装在容器中。 在打开任何腔室或拆解任何储有液体的部件之前,要准备好用合适的容器收集液体。 有关适合收集和盛接卡特彼勒产品上液体的工具及用品,参考专门出版物, NENG2500, "卡特彼勒工具和修理车间设备指南"。 按照当地法规和指令处置所有液体。 |
Show/hide table
滚热的油或液压油的压力会对人员造成伤害。 发动机停机之后,液压油的压力仍会保留在液压系统里。 对液压系统进行维修之前,如果不事先释放压力,可能会造成严重伤害。 卸下机具和其油路之前,必须先把机具放到地面上,让油先冷却,才可进行工作。 只能在发动机停机,并且加注口盖冷却到可以用徒手触摸时才能卸下加注口盖。 |
注: 为便于安装,在所有管路、软管、导线和管子上做出识别标记。 插接好所有线路、软管和管路。 这将有助于防止液体泄漏和防止污染物进入系统。
- 将软管组件 (2) 和 (3) 从转向控制阀 (1) 上断开。
Show/hide table
图 1 | g00690985 |
- 将软管组件 (6) 从转向控制阀上断开。
Show/hide table
图 2 | g00690987 |
- 将软管组件 (4) 、螺栓 (5) 和卡箍从转向控制阀上拆下。
- 将软管组件 (7) 从转向控制阀 (1) 上断开。
Show/hide table
图 3 | g00690989 |
- 将软管组件 (8) 和 (9) 从转向控制阀上断开。
Show/hide table
图 4 | g00690990 |
- 断开软管组件 (10) 。
- 拆下管组件 (11) 和 (12) 两端的螺栓。
Show/hide table
图 5 | g00690991 |
- 将管组件从机器上拆下。
- 将螺栓 (13) 从转向控制阀 (1) 上拆下。
Show/hide table
图 6 | g00690994 |
- 将工具 (A) 和适当的起吊设备安装到转向控制阀 (1) 上。 转向控制阀 (1) 的重量约为 52 kg (115 lb)。
Show/hide table
图 7 | g00690993 |
- 拆下转向控制阀 (1) 。
Caterpillar Information System:
D8R Series II Track-Type Tractor Power Train Power Train Hydraulic System
5130, 5130B and 5230 Excavators, 784B, 785B, 785C, 789B, 789C, 793B and 793C Off-Highway Truck/Tractors and 992G, 994 and 994D Wheel Loaders Vital Information Management System (VIMS) CID 0295 FMI 12 Electronic Control Module (Machine) Failed - Test
994D Wheel Loader Battery Hold-Down - Tighten
910G HYSTAT Wheel Loader Hydraulic System Oil Level - Check
5130, 5130B and 5230 Excavators, 784B, 785B, 785C, 789B, 789C, 793B and 793C Off-Highway Truck/Tractors and 992G, 994 and 994D Wheel Loaders Vital Information Management System (VIMS) CID 0295 FMI 09 Electronic Control Module (Machine) Abnormal Update - Test
2000/05/08 The Hydraulic Tank Relief Valve Has Been Repositioned in Order to Prevent Leaking {5056}
5130, 5130B and 5230 Excavators, 784B, 785B, 785C, 789B, 789C, 793B and 793C Off-Highway Truck/Tractors and 992G, 994 and 994D Wheel Loaders Vital Information Management System (VIMS) CID 0295 FMI 02 Electronic Control Module (Machine) Incorrect Signal - Test
D6M Track-Type Tractor Warranty Information
312C, 315C, 318C, 319C, 320C, 321C, 322C, 325C, 330C and M325C Excavators and 325C MHPU and 330C MHPU Mobile Hydraulic Power Units Engine and Pump Control - V2 Speed Sensor - Replace
973C Track-Type Loader Power Train Pump Drive - Disassemble
651E and 657E Wheel Tractor-Scrapers Hydraulic System Check Valve (Carry and Quick-Drop)
D8R Series II Track-Type Tractor Hydraulic System Pressure Taps
2000/03/27 Dimensions in Special Instruction are now Updated {3260, 3269, 6116, 6118, 6119, 6125, 6126, 6127, 7057, 7069, 7100}
D8R Series II Track-Type Tractor Power Train Electronic Control System Components
2000/05/08 The Hydraulic Tank Relief Valve Has Been Repositioned in Order to Prevent Leaking {5056}
3618 Engine Main Bearings
525B Wheel Skidder and 535B Wheel Skidder Engine Supplement Steering Frame Lock - Separate and Connect
988G Wheel Loader Machine Systems Steering Control Valve - Install
988G Wheel Loader Machine Systems Steering Control Valve (with Secondary Steering) - Disassemble
2000/03/27 Maintenance and Repair to a Closed Loop System for the Engine Crankcase Breather {1107, 1317}
988G Wheel Loader Machine Systems Steering Control Valve (with Secondary Steering) - Assemble
3034 Engine for Caterpillar Built Machines Fuel Injection Lines
525B and 535B Wheel Skidders Power Train Bottom Guard (Engine) - Remove and Install
525B and 535B Wheel Skidders Power Train Bottom Guard (Transmission) - Remove and Install