312C, 315C, 318C, 319C, 320C, 321C, 322C, 325C, 330C and M325C Excavators and 325C MHPU and 330C MHPU Mobile Hydraulic Power Units Engine and Pump Control - V2 Caterpillar


Speed Sensor - Replace

Usage:

322C ADX



图 1g00667337

转速传感器的安装

(1) 转速传感器

(2) 锁紧螺母

(3) 磁芯

(4) 齿轮

(5) 飞轮壳体

在更换传感器之前,先确保传感器出故障。 务必检查并确认已向传感器供电。 测量传感器的触点之间的电压。 检查磁力探头或轮齿上有无金属屑。

进行下述步骤来更换转速传感器。

  1. 将钥匙起动开关和断路开关转到 OFF 位置。

  1. 缓慢将转速传感器 (1) 拧入飞轮壳体 (5) 中,使磁芯 (3) 接触齿轮 (4) 。

  1. 逆时针转动转速传感器 (1) 。 转动量应约为 3/4 圈。

    注: 321C 为 4/5 - 1 圈。

  1. 暂时拧紧锁紧螺母 (2) 。

  1. 将发动机转速旋钮设定到位置 1(低怠速位置)。

  1. 将断路开关转到接通位置。

  1. 起动发动机。

  1. 启用维修模式。

  1. 输入维修代码 11 来显示发动机转速。

  1. 确认显示的转速为 800 RPM。

    注: 321C 为 1000 RPM。

  1. 如果没有显示正确的转速,则需顺时针转动转速传感器 (1) 。 转动量应不超过 1/3 圈。

  1. 关闭发动机。

  1. 将锁紧螺母 (2) 上紧到 25 N·m (18.4 lb ft) 的扭矩。

    注: 321C 为 29.5 ± 5 N·m (21 ± 4 lb ft)

  1. 确认使用新传感器后排除该故障。

  1. 清除错误记录。 请参阅测试和调整, "使用维修模式"。

Caterpillar Information System:

973C Track-Type Loader Power Train Pump Drive - Disassemble
651E and 657E Wheel Tractor-Scrapers Hydraulic System Check Valve (Carry and Quick-Drop)
D8R Series II Track-Type Tractor Hydraulic System Pressure Taps
910G HYSTAT Wheel Loader Fuel Tank Water and Sediment - Drain
G3304 and G3306 Engines Engine Speed Measurement
3003, 3013, 3014 and 3024 Engines for Caterpillar Built Machines Connecting Rod - Inspect
525B and 535B Wheel Skidders Backup Alarm
910G HYSTAT Wheel Loader Fuel System Primary Filter - Replace
3003, 3013, 3014 and 3024 Engines for Caterpillar Built Machines Cylinder Head - Inspect
910G HYSTAT Wheel Loader Steering Cylinder Bearings - Lubricate
988G Wheel Loader Machine Systems Piston Pump (Hydraulic Fan) - Install
910G HYSTAT Wheel Loader Tilt Cylinder Bearings and Bucket Linkage Bearings - Lubricate
D6M Track-Type Tractor Warranty Information
5130, 5130B and 5230 Excavators, 784B, 785B, 785C, 789B, 789C, 793B and 793C Off-Highway Truck/Tractors and 992G, 994 and 994D Wheel Loaders Vital Information Management System (VIMS) CID 0295 FMI 02 Electronic Control Module (Machine) Incorrect Signal - Test
2000/05/08 The Hydraulic Tank Relief Valve Has Been Repositioned in Order to Prevent Leaking {5056}
5130, 5130B and 5230 Excavators, 784B, 785B, 785C, 789B, 789C, 793B and 793C Off-Highway Truck/Tractors and 992G, 994 and 994D Wheel Loaders Vital Information Management System (VIMS) CID 0295 FMI 09 Electronic Control Module (Machine) Abnormal Update - Test
910G HYSTAT Wheel Loader Hydraulic System Oil Level - Check
994D Wheel Loader Battery Hold-Down - Tighten
5130, 5130B and 5230 Excavators, 784B, 785B, 785C, 789B, 789C, 793B and 793C Off-Highway Truck/Tractors and 992G, 994 and 994D Wheel Loaders Vital Information Management System (VIMS) CID 0295 FMI 12 Electronic Control Module (Machine) Failed - Test
D8R Series II Track-Type Tractor Power Train Power Train Hydraulic System
988G Wheel Loader Machine Systems Steering Control Valve - Remove
2000/03/27 Dimensions in Special Instruction are now Updated {3260, 3269, 6116, 6118, 6119, 6125, 6126, 6127, 7057, 7069, 7100}
D8R Series II Track-Type Tractor Power Train Electronic Control System Components
2000/05/08 The Hydraulic Tank Relief Valve Has Been Repositioned in Order to Prevent Leaking {5056}
Back to top
The names Caterpillar, John Deere, JD, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
CH-Part.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only.