Maintenance Interval Schedule
Note: All safety information, warnings, and instructions must be read and understood before you perform any operation or any maintenance procedure.
Cutting Edges and End Bits - Inspect/Replace
Engine Air Filter Primary Element - Clean/Replace
Engine Air Filter Secondary Element - Replace
Engine Air Precleaner - Clean
Equalizer Bar Pins - Inspect
Ether Starting Aid Cylinder - Replace
Fuel System - Prime
Fuses - Replace
Oil Filter - Inspect
Radiator Core - Clean
Radiator Pressure Cap - Clean/Replace
Ripper Tip and Shank Protector - Inspect/Replace
Transmission Magnetic Screen - Clean
Walk-Around Inspection
Windshield Washer Reservoir - Fill
Windshield Wipers - Inspect/Replace
Brakes, Indicators and Gauges - Test
Cab Air Filter - Clean/Replace
Cooling System Level - Check
Engine Oil Level - Check
Fuel System Primary Filter/Water Separator - Drain
Fuel Tank Water and Sediment - Drain
Hydraulic System Oil Level - Check
Seat Belt - Inspect
Track Adjustment - Check
Transmission Oil Level - Check
Windows - Clean
Equalizer Bar Center Pin - Lubricate
Pivot Shaft Oil Level - Check
Ripper Linkage and Cylinder Bearings - Lubricate
Track Pins - Inspect
Air Conditioner Belt - Inspect/Adjust/Replace
Alternator and Fan Belts - Inspect/Adjust/Replace
Battery - Inspect
Battery - Recycle
Battery, Battery Cable or Battery Disconnect Switch - Replace
Braking System - Test
Cooling System Additive (DEAC) - Add
Engine Oil and Filter - Change
Equalizer Bar Pins - Lubricate
Final Drive Oil Level - Check
Fuel System Secondary Filter - Replace
Track Adjustment - Adjust
Transmission Oil Filter - Replace
Fuel System Primary Filter - Clean/Replace
Fuel System Secondary Filter - Replace
Fuel Tank Cap and Strainer - Clean
Hydraulic System Case Drain Filter - Replace
Hydraulic System Oil Filter - Replace
Recoil Spring Compartment Oil Level - Check
Transmission Oil Filter - Replace
Transmission Oil - Change
Final Drive Oil - Change
Hydraulic System Oil - Change
Track Roller Frame - Inspect
Track Roller Frame Guides - Inspect
Cooling System Extended Life Coolant Extender - Add
Cooling System Water Temperature Regulator - Clean/Replace
Before each consecutive interval is performed, all of the maintenance requirements from the previous interval must also be performed.
When Required
Circuit Breakers - ResetCutting Edges and End Bits - Inspect/Replace
Engine Air Filter Primary Element - Clean/Replace
Engine Air Filter Secondary Element - Replace
Engine Air Precleaner - Clean
Equalizer Bar Pins - Inspect
Ether Starting Aid Cylinder - Replace
Fuel System - Prime
Fuses - Replace
Oil Filter - Inspect
Radiator Core - Clean
Radiator Pressure Cap - Clean/Replace
Ripper Tip and Shank Protector - Inspect/Replace
Transmission Magnetic Screen - Clean
Walk-Around Inspection
Windshield Washer Reservoir - Fill
Windshield Wipers - Inspect/Replace
Every 10 Service Hours or Daily
Backup Alarm - TestBrakes, Indicators and Gauges - Test
Cab Air Filter - Clean/Replace
Cooling System Level - Check
Engine Oil Level - Check
Fuel System Primary Filter/Water Separator - Drain
Fuel Tank Water and Sediment - Drain
Hydraulic System Oil Level - Check
Seat Belt - Inspect
Track Adjustment - Check
Transmission Oil Level - Check
Windows - Clean
Every 50 Service Hours or Weekly
Bulldozer Power Angling Tilt Hinge Pins - LubricateEqualizer Bar Center Pin - Lubricate
Pivot Shaft Oil Level - Check
Ripper Linkage and Cylinder Bearings - Lubricate
Track Pins - Inspect
Initial 250 Service Hours
Fuel System Secondary Filter - ReplaceEvery 250 Service Hours or Monthly
Air Conditioner - TestAir Conditioner Belt - Inspect/Adjust/Replace
Alternator and Fan Belts - Inspect/Adjust/Replace
Battery - Inspect
Battery - Recycle
Battery, Battery Cable or Battery Disconnect Switch - Replace
Braking System - Test
Cooling System Additive (DEAC) - Add
Engine Oil and Filter - Change
Equalizer Bar Pins - Lubricate
Final Drive Oil Level - Check
Fuel System Secondary Filter - Replace
Track Adjustment - Adjust
Transmission Oil Filter - Replace
Every 500 Service Hours or 3 Months
Engine Crankcase Breather - CleanFuel System Primary Filter - Clean/Replace
Fuel System Secondary Filter - Replace
Fuel Tank Cap and Strainer - Clean
Hydraulic System Case Drain Filter - Replace
Hydraulic System Oil Filter - Replace
Recoil Spring Compartment Oil Level - Check
Transmission Oil Filter - Replace
Every 1000 Service Hours or 6 Months
Rollover Protective Structure (ROPS) - InspectTransmission Oil - Change
Every 2000 Service Hours or 1 Year
Engine Valve Lash and Fuel Injector Timing - CheckFinal Drive Oil - Change
Hydraulic System Oil - Change
Track Roller Frame - Inspect
Track Roller Frame Guides - Inspect
Every 3000 Service Hours or 2 Years
Cooling System Coolant (DEAC) - ChangeCooling System Extended Life Coolant Extender - Add
Cooling System Water Temperature Regulator - Clean/Replace
Every 6000 Service Hours or 4 Years
Cooling System Extended Life Coolant - ChangeFirst 250 Service Hours (or at first oil change)
Engine Valve Lash and Fuel Injector Timing - CheckCaterpillar Information System:
988G Wheel Loader Engine Supplement Engine and Torque Converter - Install
3003, 3013, 3014 and 3024 Engines for Caterpillar Built Machines Fuel System Pressure - Test
910G HYSTAT Wheel Loader Stopping the Engine
3054 Engine Air in Fuel - Test
910G HYSTAT Wheel Loader Stopping the Machine
914G Compact Wheel Loader and IT14G Integrated Toolcarrier Transmission Electronic Control System Switches
3003, 3013, 3014 and 3024 Engines for Caterpillar Built Machines Gear Group (Front) - Time
651E and 657E Wheel Tractor-Scrapers Hydraulic System General Information
910G HYSTAT Wheel Loader Shipping the Machine
980G Wheel Loader Power Train Fender (Front and Rear) - Remove and Install
980G Wheel Loader Power Train Transmission to Torque Converter - Connect
980G Wheel Loader Power Train Transmission from Torque Converter - Separate
D6M Track-Type Tractor Product Identification Number, Serial Number and EU's CE Plate Locations
545 Wheel Skidder Refrigerant Accumulator (With Desiccant) - Replace
3003, 3013, 3014 and 3024 Engines for Caterpillar Built Machines Fuel System - Prime
2000/03/27 A Stronger Carrier Roller Mounting Bracket Improves Reliability {4154}
3003, 3013, 3014 and 3024 Engines for Caterpillar Built Machines Finding Top Center Position for No. 1 Piston
988G Wheel Loader Engine Supplement Engine from Torque Converter - Separate
988G Wheel Loader Engine Supplement Engine to Torque Converter - Connect
988G Wheel Loader Engine Supplement Engine Oil Cooler - Remove - Engine In Chassis
651E and 657E Wheel Tractor-Scrapers Air System and Brakes Solenoid Valve (Apron)
994D Wheel Loader Battery - Clean
3003, 3013, 3014 and 3024 Engines for Caterpillar Built Machines Engine Valve Lash - Inspect/Adjust
910G HYSTAT Wheel Loader Cab Door