Flywheel Housing - Remove and Install
Removal Procedure
Show/hide table
Required Tools     | |||
---|---|---|---|
Tool     | Part Number     | Part Description     | Qty     |
A     | 135-7575     | Link Bracket     | 1     |
Start By:
- Remove the electric starting motor. Refer to Disassembly and Assembly, "Electric Starting Motor- Remove and Install".
- Remove the crankshaft rear seal. Refer to Disassembly and Assembly, "Crankshaft Rear Seal - Remove".
Show/hide table
NOTICE |
---|
Keep all parts clean from contaminants. Contaminants may cause rapid wear and shortened component life. |
- Install Tool (A), a strap, and a suitable lifting device onto flywheel housing (1) .
Show/hide table
Illustration 1 | g00528388 |
- Remove twelve bolts (2) and the washers that secure flywheel housing (1) to the cylinder block.
- Remove flywheel housing (1). The weight of the flywheel is 30 kg (66 lb).
Installation Procedure
Show/hide table
Required Tools     | |||
---|---|---|---|
Tool     | Part Number     | Part Description     | Qty     |
A     | 138-7575     | Link Bracket     | 1     |
Show/hide table
NOTICE |
---|
Keep all parts clean from contaminants. Contaminants may cause rapid wear and shortened component life. |
- Check the condition of two dowels (4). If dowels (4) are damaged, use new parts for replacement.
Show/hide table
Illustration 2 | g00528389 |
- Clean old gasket material (3) from the surfaces of the cylinder block and the flywheel housing that contact each other. Install a new gasket on the cylinder block (not shown).
- Install flywheel housing (1) .
Show/hide table
Illustration 3 | g00528388 |
- Install the washers and twelve bolts (2) in order to secure flywheel housing (3) to the cylinder block.
- Remove Tool (A) .
End By:
- Install the electric starting motor. Refer to Disassembly and Assembly, "Electric Starting Motor- Remove and Install".
- Install the crankshaft rear seal. Refer to Disassembly and Assembly, "Crankshaft Rear Seal - Install".
Caterpillar Information System:
963B Track-Type Loader Fuses - Replace
973 Track-Type Loader Power Train System Schematics
994D Air System Wheel Loader Pressure Sensor (Air Tank)
623F Wheel Tractor-Scraper Machine Systems Tractor and Scraper - Connect
623F Wheel Tractor-Scraper Machine Systems Tractor and Scraper - Separate
623F Wheel Tractor-Scraper Hydraulic System Pilot Control Valve (Three Functions)
994D Air System Wheel Loader Governor (Air Compressor)
515 Wheel Skidder and 525 Wheel Skidder Cooling System Coolant Sample - Obtain
963B Track-Type Loader Circuit Breakers - Reset
D9R Track-Type Tractor Parking Brake Control
515 Wheel Skidder and 525 Wheel Skidder Cooling System Coolant Extender (ELC) - Add
D9R Track-Type Tractor Light Switches
515 Wheel Skidder and 525 Wheel Skidder Ether Starting Aid Cylinder - Replace
994D Air System Wheel Loader Air Tank
623F Wheel Tractor-Scraper Machine Systems Brake Actuator - Remove
623F Wheel Tractor-Scraper Machine Systems Brake Actuator - Install
515 Wheel Skidder and 525 Wheel Skidder Transmission and Grapple Electronic Control System Troubleshooting Switch (Tong Auto/Manual)
623F Wheel Tractor-Scraper Machine Systems Brake Actuator - Remove
623F Wheel Tractor-Scraper Machine Systems Brake Actuator - Install
994D Air System Wheel Loader Solenoid Valve (Air Start)
3516B Engine for Caterpillar Built Machines Customer Parameters Worksheet
994D Air System Wheel Loader Solenoid Valve (Automatic Lubrication)
980G Wheel Loader Machine Systems Pilot Valve (Oil Manifold) - Assemble
994D Air System Wheel Loader Solenoid Valve (Air Horn)