Steering Clutch and Brake Control Valve - Disassemble
Disassembly Procedure
Start By:
- Remove the steering clutch and the brake valve. Refer to Disassembly and Assembly, "Steering Clutch and Brake - Remove" for the machine that is being serviced.
- Remove two wire ties (2) .
Show/hide table
Illustration 1 | g00676560 |
Show/hide table
Illustration 2 | g00676567 |
- Remove four bolts (1) and remove plate (3) .
- Remove manifold (4) and washers (5) .
Show/hide table
Illustration 3 | g00676570 |
- Remove nut (9), solenoid (8), and stem (7) from manifold (4) .
Show/hide table
Illustration 4 | g00676573 |
- Remove O-rings (10) from stem (7) .
- Remove O-ring (6) from manifold (4) .
- Remove two dowels (11) and plate (12) .
Show/hide table
Illustration 5 | g00676576 |
Show/hide table
Illustration 6 | g00677801 |
- Remove O-ring (14) from valve (15) .
Show/hide table
Illustration 7 | g00676577 |
- Remove bolts (13) and remove valve (15) .
- Remove O-ring seal (16) from valve (15) .
Show/hide table
Illustration 8 | g00676584 |
- Remove bolts (17) and remove plate (18) from valve (15) .
- Remove four O-ring seals (19) from valve (15) .
Show/hide table
Illustration 9 | g00676592 |
Show/hide table
Illustration 10 | g00676598 |
- Remove two springs (20) and (21) from each bore.
- Remove four pistons (22) from valve (15) .
Show/hide table
Illustration 11 | g00676600 |
- Remove four plugs (26) and seals (25) from valve (15) .
Show/hide table
Illustration 12 | g00676603 |
- Remove springs (24) and spools (23) .
- Remove plate (27) from manifold (28) .
Show/hide table
Illustration 13 | g00676609 |
Show/hide table
Illustration 14 | g00676612 |
- Remove dowels (30) .
- If necessary, remove plugs (29) from plate (27) .
- Remove O-ring seal (31) from manifold (28) .
Note: Plugs (29) are not interchangeable. DO NOT MIX.
Show/hide table
Illustration 15 | g00676614 |
Show/hide table
Illustration 16 | g00676619 |
- Remove nut (33), spacer (32), and solenoid (34) .
- Remove stem (35) .
- Remove O-ring seals (36) from stem (35). Repeat this procedure for the remaining solenoid assemblies.
- Remove two dowel pins (37) from manifold (28) .
Show/hide table
Illustration 17 | g00676620 |
Show/hide table
Illustration 18 | g00676624 |
Show/hide table
Illustration 19 | g00676626 |
- Install M16 x 2.0 Bolt (38) in spool assembly (39). Remove the two spool assemblies.
Caterpillar Information System:
D5M Track-Type TractorPower Train Steering Clutch and Brake Control Valve - Assemble
D5M Track-Type TractorPower Train Steering Clutch and Brake - Disassemble
D5M Track-Type TractorPower Train Steering Clutch and Brake - Assemble
D5M Track-Type TractorPower Train Sprocket Segment - Remove and Install
D5M Track-Type TractorPower Train Recoil Spring - Remove
D5M Track-Type TractorPower Train Recoil Spring - Install
D5M Track-Type TractorPower Train Priority Valve - Remove
D5M Track-Type TractorPower Train Priority Valve - Install
D5M Track-Type TractorPower Train Priority Valve - Disassemble
D5M Track-Type TractorPower Train Priority Valve - Assemble
D5M Track-Type TractorPower Train Power Train Oil Pump - Remove
D5M Track-Type TractorPower Train Power Train Oil Pump - Install
D5M Track-Type TractorPower Train Steering Clutch and Brake Control Valve - Install
D5M Track-Type TractorPower Train Steering Clutch and Brake Control Valve - Remove
D5M Track-Type TractorPower Train Torque Converter - Assemble
D7R Track-Type TractorPower Train Equalizer Bar
3306C Engines for Caterpillar Built Machines Governor
D5M Track-Type TractorPower Train Torque Converter - Disassemble
515 Wheel Skidder and 525 Wheel Skidder Drive Shaft Spline (Front) - Lubricate
D5M Track-Type TractorPower Train Torque Converter - Install
D5M Track-Type TractorPower Train Torque Converter - Remove
D5M Track-Type TractorPower Train Torque Converter Outlet Relief Valve - Assemble
D5M Track-Type TractorPower Train Torque Converter Outlet Relief Valve - Disassemble
D5M Track-Type TractorPower Train Torque Converter Outlet Relief Valve - Install