Steering Clutch - Remove and Install
Removal Procedure
Start By:
- Remove the hydraulic controls for the brake and the actuating mechanisms. Refer to Disassembly and Assembly, "Brake Hydraulic Control and Actuating Mechanism - Remove".
Show/hide table
NOTICE |
---|
Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting and repair of the machine. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids. Refer to Special Publication, NENG2500, "Caterpillar Tools and Shop Products Guide", for tools and supplies suitable to collect and contain fluids in Caterpillar machines. Dispose of all fluids according to local regulations and mandates. |
- Drain the oil from the steering clutch case.
- Remove plug (1) .
Show/hide table
Illustration 1 | g00417258 |
- Remove bolts (2) that hold the steering clutch to the steering clutch hub.
Show/hide table
Illustration 2 | g00417304 |
Note: Remove all bolts (2) and (3) except for one on each side of the steering clutch. Turn the sprocket or turn the track in order to remove the bolts.
- Remove bolts (3) through the opening that is in the steering clutch case. Plug (1) was removed at this location.
- Install two 3/8 inch - 16 NC bolts that are 4 inches long in the brake bands, as shown.
Show/hide table
Illustration 3 | g00417305 |
- Attach an appropriate lifting device and a hoist to the brake bands and remove the last two bolts that hold the steering clutch in position.
- Remove steering clutch (4) from the machine. The weight of the steering clutch is 113 kg (250 lb).
Installation Procedure
- Attach an appropriate lifting device and a hoist to steering clutch (4) .
Show/hide table
Illustration 4 | g00417305 |
- Put the steering clutch (4) in position between the steering clutch hub and the flange.
- Install two bolts in order to hold the clutch in position. Remove the hoist.
- Put 5P-3931 Anti-Seize Compound on the threads of all the bolts.
- Install bolts (2) and (3) that hold the steering clutch in position. Tighten the bolts to a torque of 270 ± 25 N·m (200 ± 20 lb ft).
Show/hide table
Illustration 5 | g00417304 |
- Install plug (1) in the steering clutch case.
Show/hide table
Illustration 6 | g00417258 |
End By:
- Install the hydraulic controls for the brake and the actuating mechanisms. Refer to Disassembly and Assembly, "Brake Hydraulic Control and Actuating Mechanism - Install".
- Fill the bevel gear case and steering clutch case with oil to the correct level. Refer to Operation and Maintenance Manual.
Caterpillar Information System:
3126E and 3126B Commercial and Truck Engines Emissions Certification Film
966G Wheel Loader and 972G Wheel Loader Machine Systems Vane Pump (Pilot and Braking) - Install
966G Wheel Loader and 972G Wheel Loader Machine Systems Vane Pump (Pilot and Braking) - Remove
966G Wheel Loader and 972G Wheel Loader Power Train Torque Converter and Pump Drive Housing
994D Wheel Loader Power Train Oscillating Axle (Rear)
992G Wheel Loader Machine Systems Ride Control Accumulator - Remove
966G Wheel Loader and 972G Wheel Loader Power Train Torque Converter
994D Wheel Loader Power Train Input Transfer Gears
966G Wheel Loader and 972G Wheel Loader Machine Systems Pilot Operated Hydraulic Control - Assemble
966G Wheel Loader and 972G Wheel Loader Machine Systems Pilot Valve (Steering) - Assemble
966G Wheel Loader and 972G Wheel Loader Machine Systems Pilot Valve (Steering) - Disassemble
611 Wheel Tractor-Scraper 3306B Engine Supplement Radiator - Disassemble
D9R Track-Type Tractor Plate Locations and Film Locations
966G Wheel Loader and 972G Wheel Loader Power Train Speed Sensor (Torque Converter Output)
966G Wheel Loader and 972G Wheel Loader Machine Systems Vane Pump (Pilot and Braking) - Disassemble
992G Wheel Loader Machine Systems Ride Control Accumulator - Install
966G Wheel Loader and 972G Wheel Loader Power Train Transmission Oil Pump
966G Wheel Loader and 972G Wheel Loader Machine Systems Vane Pump (Pilot and Braking) - Assemble
3003, 3013, 3014 and 3024 Engines for Caterpillar Built Machines Camshaft
992G Wheel Loader Machine Systems Ride Control Accumulator - Assemble
966G Wheel Loader and 972G Wheel Loader Power Train Oil Filter (Power Train)
994D Wheel Loader Power Train Electronic Control Module (Power Train) - Pinout Specifications
IT14G Integrated Toolcarrier and 914G Wheel Loader Machine Systems Window Wiper and Wiper Motor (Rear) - Remove
613C Series II Wheel Tractor-Scraper Machine Systems Elevator Chain Adjustment Idler - Disassemble