Cylinder Head Valves
Show/hide table
Illustration 1 | g01014579 |
Note: Refer to Guidelines For Reusable Parts, SEBF8002 and SEBF8034, "Valves And Valve Springs" in order to check used valves and valve springs.
(1) 4N-5906 Spring
- Length under test force ... 54.99 mm (2.165 inch)
- Test force ... 344 ± 34 N (77.3 ± 7.6 lb)
- Length at valve open position ... 42.93 mm (1.690 inch)
- Free length after test ... 62.7 mm (2.47 inch)
- Outside diameter ... 31.75 mm (1.250 inch)
- Test force ... 344 ± 34 N (77.3 ± 7.6 lb)
(2) Height to top of valve guide ... 24 ± 0.8 mm (0.9449 ± 0.0315 inch)
(3) Diameter of new valve stem
- Inlet ... 9.441 ± 0.008 mm (0.3717 ± 0.0003 inch)
- Exhaust ... 9.441 ± .01 mm (0.3717 ± 0.0004 inch)
Minimum diameter of the valve stem
- Inlet ... 9.309 mm (0.3665 inch)
- Exhaust ... 9.309 mm (0.3665 inch)
Bore in a new guide ... 9.502 mm (0.3741 inch)
(4) Diameter of valve head
- Inlet ... 44.98 ± 0.13 mm (1.771 ± 0.005 inch)
- Exhaust ... 41.81 ± 0.13 mm (1.646 ± 0.005 inch)
(5) Angle of valve face ... 19.25 ± 0.25 degrees
Show/hide table
Illustration 2 | g01014632 |
(6) Depth of bore in head for new valve seat insert ... 12 ± .1 mm (0.4724 ± 0.0039 inch)
(7) Diameter of valve seat insert
- Inlet ... 46.025 ± .015 mm (1.8120 ± 0.0006 inch)
- Exhaust ... 42.840 ± .015 mm (1.6866 ± 0.0006 inch)
Bore in head for valve seat insert
- Inlet ... 45.949 ± 0.025 mm (1.8090 ± 0.0010 inch)
- Exhaust ... 42.774 ± .025 mm (1.6840 ± 0.0010 inch)
(8) Angle of valve insert face ... 20.25 ± 0.5 degrees
Caterpillar Information System:
G3500B Engines Engine Oil Lines
C15 and C18 Industrial Engines Engine Oil Pan - Remove and Install
G3520B Industrial Engine Oxygen Sensor Signal
G3520B Industrial Engine Oxygen Sensor Buffer Supply
3500B High Displacement Air Inlet and Exhaust Lines
G3520B Industrial Engine Oxygen Sensor - Calibrate
G3520B Industrial Engine Engine Speed/Timing Sensor - Calibrate
C27 and C32 Industrial and Petroleum Engines Intermittent Low Power or Power Cutout
2004/07/01 Some Older Mechanical Unit Injectors are Being Cancelled {1290}
3126E Truck Engines Maintenance Interval Schedule - Engines with a Deep Oil Sump
3126E Truck Engines Maintenance Interval Schedule - Engines with a Shallow Oil Sump
2004/10/01 Reduced Oil Change Intervals {7542}
TH31-C9I, TH31-C9P, TH31-C9T, TH35-C13I, TH35-C13T, TH35-C15I and TH35-C15T Petroleum Power Train Packages and TH31-E61 and TH35-E81 Petroleum Transmissions Transmission Oil Filter (Transmission)
3126E Truck Engines Reference Material
C4.4 (Mech) Industrial Engine Battery - Replace
C4.4 (Mech) Industrial Engine Battery or Battery Cable - Disconnect
C7 Marine Engines Fuel Cooler - Remove and Install
C7 Marine Engines Engine Sensors - Remove and Install
3500 Industrial Engines Auxiliary Water Pump
G3500 Engines Cooling System Coolant (NGEC) - Change
C15 and C18 Industrial Engines Flywheel Housing - Remove and Install
XQ125 Generator Set Driven Equipment - Check
C15 Petroleum Generator Set Engines Fuel Transfer Pump
C3.3 Industrial Engine Engine Air Cleaner Element (Single Element) - Inspect/Replace