Air/Hydraulic Cylinder (Brake) - Assemble
Assembly Procedure
Show/hide table
Required Tools     | |||
---|---|---|---|
Tool     | Part Number     | Part Description     | Qty     |
A     | 1P-1854     | Retaining Ring Pliers     | 1     |
- Clean all parts and inspect all parts. If any parts are worn or damaged, use new Caterpillar parts for replacement.
- Install felt wiper seal (21) and spring (22) to seal carrier (10) . Install shaft (17) and cup seal (20) to piston assembly (18) . Install O-ring seal (19) to shaft (17) .
Show/hide table
Illustration 1 | g00402009 |
- Connect seal carrier (10) to piston assembly (18) . Install two nuts (16) to shaft (17) . Torque two nuts to 27 ± 3 N·m (20 ± 2 lb ft) .
Show/hide table
Illustration 2 | g00402008 |
- Install O-ring seal (14) and two vee seals (15) to retainer (6) .
Show/hide table
Illustration 3 | g00402006 |
- Install valve seal (13) to retainer valve (9) .
Show/hide table
Illustration 4 | g00402005 |
- Install ring seal (11) and vee seal (12) to piston (8) .
Show/hide table
Illustration 5 | g00402003 |
- Install spring (5) , retainer (6) , retaining ring (7) , retainer valve (9) and piston (8) to seal carrier (10) .
Show/hide table
Illustration 6 | g00402002 |
- Compress spring (5) and hold retainer (6) , as shown. Use Tool (A) to install retaining ring (7) to piston (8) .
Show/hide table
Illustration 7 | g00402001 |
- Compress spring (5) in order to install retainer (6) to body (3) . Torque retainer (6) to 41 ± 13 N·m (30 ± 10 lb ft) .
Show/hide table
Illustration 8 | g00401756 |
- Connect cylinder (2) to body (3) . Install six nuts (1) to cylinder (2) . Torque six nuts (1) to 15 ± 3 N·m (11 ± 2 lb ft). Install overstroke switch (4) to body (3) . Torque overstroke switch (4) to 8 ± 3 N·m (6 ± 2 lb ft) .
Show/hide table
Illustration 9 | g00401755 |
End By: Install the brake air/hydraulic cylinder. Refer to Disassembly and Assembly, "Air/Hydraulic Cylinder (Brake) - Install". The information is in this manual.
Caterpillar Information System:
631E Series II Wheel Tractor-Scrapers Cooling System Coolant (DEAC) - Change
Field Installation of the Hystat Joystick Effort and Modulation Springs{5059} Field Installation of the Hystat Joystick Effort and Modulation Springs{5059}
992G Wheel Loader and 854G Wheel Dozer Power Train Wheel Bearings - Adjust
966G Wheel Loader and 972G Wheel Loader Machine Systems Diverter Valve (Ride Control) - Remove
994D Wheel Loader Power Train Pressure Sensor (Impeller Clutch Oil)
990 Wheel Loader, 990 Series II Wheel Loader and 844 Wheel Dozer Power Train Wheel Bearings - Adjust
992G Wheel Loader and 854G Wheel Dozer Steering System Limit Switch (STIC Lockout Control) - Adjust
854G Wheel Dozer Machine Systems Lift Cylinder Mounting - Remove and Install
994D Wheel Loader Power Train Filter (Power Train)
IT14G Integrated Toolcarrier Fire Extinguisher Location
854G Wheel Dozer Machine Systems Main Control Valve - Install
854G Wheel Dozer Machine Systems Main Control Valve - Remove
994D Wheel Loader Power Train Transmission Planetary
902 and 906 Compact Wheel Loaders Braking System Master Cylinder
637E Series II Wheel Tractor-Scrapers Cooling System Coolant (DEAC) - Change
627F Wheel Tractor-Scraper Engine Air Precleaner - Clean
854G Wheel Dozer Machine Systems Main Control Valve - Disassemble
854G Wheel Dozer Machine Systems Main Control Valve - Assemble
D6R Track-Type Tractor Power Train Drive Shaft
992G Wheel Loader and 854G Wheel Dozer Power Train Input Transfer Gears - Adjust
992G Wheel Loader and 854G Wheel Dozer Power Train Output Transfer Gears - Adjust
992G Wheel Loader and 854G Wheel Dozer Power Train Differential Pinion Preload - Adjust
992G Wheel Loader and 854G Wheel Dozer Power Train Differential Backlash and Bearings - Adjust
D6R Series II Track-Type Tractor Power Train Pivot Shaft