Engine Oil Cooler - Remove and Install
Removal Procedure
Start By:
- Remove the transmission oil cooler. Refer toDisassembly and Assembly, "Transmission Oil Cooler - Remove". The information is in this manual.
Show/hide table
NOTICE |
---|
Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting and repair of the machine. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids. Refer to Special Publication, NENG2500, "Caterpillar Tools and Shop Products Guide", for tools and supplies suitable to collect and contain fluids in Caterpillar machines. Dispose of all fluids according to local regulations and mandates. |
- Drain the engine oil from the engine crankcase into a suitable container. The capacity of the engine crankcase is 24 L (25.5 qt).
- Remove four bolts (1) that secure the engine oil cooler to oil filter base (2) .
Show/hide table
Illustration 1 | g00345150 |
- Remove four bolts (3) from engine oil cooler (4). Remove engine oil cooler (4) and two gaskets from the engine.
Show/hide table
Illustration 2 | g00345148 |
- Remove four bolts and elbow (5) from engine oil cooler (4). Remove bolt (8) and elbow (7) from engine oil cooler (4). Remove O-ring seals (6) from elbows (5) and (7) .
Show/hide table
Illustration 3 | g00348013 |
- Use dowel rod (9) to clean engine oil cooler (4). The diameter of dowel rod (9) is 3.96 mm (.156 inch).
Show/hide table
Illustration 4 | g00345043 |
Installation Procedure
- Inspect the O-ring seals and the gaskets that were removed from the assembly for wear or damage. If the O-ring seals and the gaskets are worn or damaged, use new Caterpillar parts for replacement.
- Install O-ring seals (6) in elbows (5) and (7). Install elbows (5) and (7) on engine oil cooler (4) .
Show/hide table
Illustration 5 | g00348013 |
- Install the gaskets on engine oil cooler (4). Install engine oil cooler (4) and bolts (3) to the engine.
Show/hide table
Illustration 6 | g00345148 |
- Position the engine oil cooler to oil filter base (2). Install four bolts (1) that secure the engine oil cooler to oil filter base (2) .
Show/hide table
Illustration 7 | g00345150 |
End By: Install the transmission oil cooler. Refer to Disassembly and Assembly, "Transmission Oil Cooler - Install". The information is in this manual.
Caterpillar Information System:
631E Series II Wheel Tractor-Scrapers Battery Electrolyte Level - Check
3408E and 3412E Engines for Caterpillar Built Machines Fuel Filter Base
950G Wheel Loader, 962G Wheel Loader and IT62G Integrated Toolcarrier Engine Supplement Governor and Fuel Transfer Pump - Remove
950G Wheel Loader, 962G Wheel Loader and IT62G Integrated Toolcarrier Engine Supplement Water Pump - Remove and Install
938G Wheel Loader and IT38G Integrated Toolcarrier Engine Supplement Water Temperature Regulator - Remove and Install
627F Wheel Tractor-Scraper Service Brake Control
D11R Track-Type Tractor Hydraulic System Fan Drive Pump - 145-0772
621F Wheel Tractor-Scraper Service Brake Control
611 Wheel Tractor-Scraper 3306B Engine Supplement Transmission Oil Cooler - Remove
D11R Track-Type Tractor Hydraulic System Pilot Control Valve
Schedules For The On-Fuel Injection Test Stand{0782, 1264} Schedules For The On-Fuel Injection Test Stand{0782, 1264}
631E Series II Wheel Tractor-Scrapers Battery or Battery Cable - Inspect/Replace
D6R Track-Type Tractor Cooling System Coolant (DEAC) - Change
950G Wheel Loader, 962G Wheel Loader and IT62G Integrated Toolcarrier Power Train Limited Slip Differential Disc End Play Check - Check
854G Wheel Dozer Hydraulic Fan Valve Screen - Replace
D3C Series III, D4C Series III and D5C Series III Hystat Track-Type Tractors Power Train Motor Tracking and Fast Mode - Test
854G Wheel Dozer Machine Systems Piston Pump (Steering) - Remove
854G Wheel Dozer Machine Systems Piston Pump (Steering) - Install
D11R Track-Type Tractor Hydraulic System Cooler Bypass Valve
950G Wheel Loader, 962G Wheel Loader and IT62G Integrated Toolcarrier Engine Supplement Aftercooler - Remove and Install
854G Wheel Dozer Machine Systems Gear Pump (Secondary Steering) - Remove
D11R Track-Type Tractor Hydraulic System Bulldozer Lift Cylinder
854G Wheel Dozer Machine Systems Gear Pump (Secondary Steering) - Install
854G Wheel Dozer Machine Systems Gear Pump (Secondary Steering) - Disassemble