Torque Divider Scavenge Oil Pump - Assemble
Assembly Procedure
Show/hide table
Required Tools     | |||
Tool     | Part Number     | Part Description     | Qty     |
A     | 1P-0510     | Driver Group     | 1     |
Show/hide table
NOTICE |
---|
Keep all parts clean from contaminants. Contaminants may cause rapid wear and shortened component life. |
Note: Check the condition of all seals and of all components. If any parts are worn or damaged, use new parts for replacement.
- Install the bearings in cover (1) with tooling (A). Install the bearings until the bearings are 3.1 mm (0.12 inch) below the machined surface of the cover.
Show/hide table
Illustration 1 | g00460158 |
Show/hide table
Illustration 2 | g00460159 |
- Install the bearings in the body assembly with tooling (A). Install the bearings until the bearings are 3.0 mm (0.12 inch) below the inside surface of the body assembly.
- Put the ring on the shaft. Install key (2) and gear (4). Install ring (3) .
- Assemble the other shaft. Follow Step 9 in order to assemble the shaft.
- Put clean SAE 30 oil on the parts of the scavenge pump that is for the torque divider.
- Install the shaft and the gear in the body.
- Install the shaft and gear (5) in cover (1) .
- Put bolts (6) and locks in the body.
Show/hide table
Illustration 3 | g00460160 |
- Heat gear (7) to a maximum temperature of 149°C (300°F). Install the gear on the shaft.
- Put the body on cover (1). Tighten bolts (6) and bend the locks over the bolts. Install nut (8) and the washer. Tighten the nut to torque of 55 ± 5 N·m (41 ± 4 lb ft).
Note: The pump must turn freely by hand after the scavenge pump is assembled.
End By: Install the scavenge pump that is for the torque divider. Refer to Disassembly and Assembly, "Torque Divider Scavenge Oil Pump - Remove and Install".
Caterpillar Information System:
627F Wheel Tractor-Scraper Wheel Scraper Power Train Differential and Bevel Gear - Scraper
613C Series II Wheel Tractor 3116 Engine Supplement Engine Front Support - Install
994D Wheel Loader Battery Disconnect Switch
627F Wheel Tractor-Scraper Changing Direction and Speed
D6G Track-Type Tractor Power Train Torque Divider Scavenge Oil Pump - Disassemble
D6G Track-Type Tractor Power Train Torque Divider Scavenge Oil Pump - Remove and Install
621F, 623F and 627F Wheel Tractor-Scrapers Steering System Metering Pump (Steering)
994D Wheel Loader Plate Locations and Film Locations
950G Wheel Loader, 962G Wheel Loader and IT62G Integrated Toolcarrier Braking System Hydraulic Oil Contamination - Test
D6G Track-Type Tractor Power Train Universal Joint - Remove and Install
627F Wheel Tractor-Scraper Auger Control
D6G Track-Type Tractor Power Train Lubrication Relief Valve - Disassemble and Assemble
613C Series II Wheel Tractor 3116 Engine Supplement Engine - Install
627F Wheel Tractor-Scraper Braking Operation
613C Series II Wheel Tractor-Scraper Machine Systems Vane Pump (Hydraulic and Steering) - Assemble
950G Wheel Loader, 962G Wheel Loader and IT62G Integrated Toolcarrier Steering System Steering System Troubleshooting - HMU Steering
D6G Track-Type Tractor Power Train Torque Divider - Install
D6G Track-Type Tractor Power Train Torque Divider - Remove
966G Wheel Loader and 972G Wheel Loader Hydraulic System Check Valve (Ride Control)
D6G Track-Type Tractor Power Train Torque Divider - Disassemble
D6G Track-Type Tractor Power Train Torque Divider - Assemble
613C Series II Wheel Tractor-Scraper Machine Systems Vane Pump (Hydraulic and Steering) - Install
613C Series II Wheel Tractor-Scraper Machine Systems Vane Pump (Hydraulic and Steering) - Remove
613C Series II Wheel Tractor-Scraper Machine Systems Vane Pump (Hydraulic and Steering) - Disassemble