Engine Oil Pan
Show/hide table
图 1 | g03364664 |
俯视图 |
Show/hide table
图 2 | g03364665 |
右视图 |
Show/hide table
350-3025 油底壳总成 的技术规格     | |||
项目     | 数量     | 零件     | 技术规格说明     |
1     | 1     | 5P-5846 O 形密封圈     | 装配前,用润滑剂稍微润滑即将密封的孔。     |
2     | 3     | 206-7331 排放塞     | 拧紧至扭矩为 70 ± 15 N·m (52 ± 11 lb ft)。     |
3     | 1     | 5P-8068 O 形密封圈     | 装配前,用润滑剂稍微润滑即将密封的孔。     |
Show/hide table
图 3 | g03376664 |
拧紧顺序 |
Show/hide table
图 4 | g03376665 |
再次拧紧顺序 |
Show/hide table
项目     | 数量     | 零件     | 技术规格说明     | |
4     | 40     | 2P-3205 螺栓     | 装配发动机油底壳时,使用下述步骤:     | |
油底壳的密封表面应没有机油、碎屑、垫片材料或任何其他密封胶。 | ||||
必须在涂抹密封胶后的 10 分钟内组装油底壳并将其拧紧至缸体上。 | ||||
1. 向下列位置涂抹 3 至 5 mm (0.1 至 0.2 in) 的超蓝 Loctite 587: 前壳体和缸体前部的连接点。 飞轮壳和缸体后部的连接点。 |
||||
2. 按照图 3 中所示的数字顺序,将螺栓 1 至螺栓 40 拧紧至扭矩为 40 ± 5 N·m (30 ± 4 lb ft)。 |
||||
3. 按照图 4 中所示的数字顺序,再次将螺栓 1 至螺栓 40 拧紧至扭矩为 47 ± 5 N·m (35 ± 4 lb ft)。 |
Caterpillar Information System:
3512B Engine Product Storage
3508B, 3512B, and 3516B High Displacement Generator Sets Gauges and Indicators
3406E, C-10 and C-12 On-highway Engines Tachometer Circuit - Test
325D and 329D Excavators Stopping the Engine
2006/01/01 A New Type of Main Bearing is Available {1203}
2006/01/02 A New Type of Main Bearing is Available {1203}
2005/12/26 A New Type of Main Bearing is Available {1203}
ES12F, UPS 1000S and UPS 1200S Uninterruptible Power Supplys Battery - Replace - Controller Board
C27 and C32 Engines for Caterpillar Built Machines Housing (Front)
ES12F, UPS 1000S and UPS 1200S Uninterruptible Power Supplys Battery - Replace - "APC2" Controller Board
C7 and C9 On-Highway Engines Diesel Particulate Filter Circuit - Test
C7 and C9 On-Highway Engines Low Power/Poor or No Response to Throttle
325D and 329D Excavators Power Receptacle - If Equipped
3406E, C-10 and C-12 On-highway Engines Vehicle Speed and Speedometer Circuit - Test
3406E On-Highway Engine Rocker Arm and Shaft - Remove
3408E and 3412E Engines for Caterpillar Built Machines Coolant Conditioner Base
3406E, C-10 and C-12 On-highway Engines Warning Lamp Circuit - Test
C15 and C18 Engines for Caterpillar Built Machines Water Temperature Regulator Housing
3508B, 3512B, and 3516B High Displacement Generator Sets Starting the Engine
C15 and C18 Industrial Engines Flywheel Adapter
C15 and C18 Industrial Engines Flywheel Adapter
C15 and C18 Industrial Engines Flywheel Housing
3406E, C-10 and C-12 On-highway Engines Engine Speed/Timing Sensor - Calibrate
2004/07/26 Caterpillar Remanufactured Products Group Announces the Introduction of the Help Line Reference Tool {1000, 7000}