Electric Starting Motor
Show/hide table
Illustration 1 | g01100499 |
Show/hide table
Illustration 2 | g01100501 |
When the electric starting motor is viewed from the drive end, the motor rotates in the following direction. ... Clockwise
No load conditions at
- Minimum speed with no load ... 7643 ± 1683 rpm
- Maximum current with no load ... 76.5 ± 14.5 amp
- Voltage ... 23 V
- Maximum current with no load ... 76.5 ± 14.5 amp
(1) Battery terminal
- Maximum number of cable or wire terminals between the nuts ... 3
- Tighten the nut on the battery terminal to the following torque. ...
30.5 ± 3.5 N·m (22 ± 3 lb ft) - Tighten the nut on the battery terminal to the following torque. ...
(2) Ground terminal
- Tighten the nut on the ground terminal to the following torque. ...
30.5 ± 3.5 N·m (22 ± 3 lb ft)
(3) Ground terminal
- Tighten the nut on the ground terminal to the following torque. ...
2.25 ± 0.25 N·m (20 ± 2 lb in)
(4) Motor terminal
- Tighten the nut on the motor terminal to the following torque. ...
30.5 ± 3.5 N·m (22 ± 3 lb ft)
(5) Switch terminal
- Tighten the nut on the switch terminal to the following torque. ...
2.25 ± 0.25 N·m (20 ± 2 lb in)
Note: The wire terminal that is on the switch terminal must be insulated with heat shrink tubing. Do not use molded terminals.
(6) Motor frame terminal
- Tighten the nut on the motor frame terminal to the following torque. ...
8 ± 3 N·m (70 ± 27 lb in)
Current draw at 20 V and
- Pull-in windings ... 57 Amp
- Hold-in windings ... 16 Amp maximum
Caterpillar Information System:
3406E, C-10 and C-12 On-highway Engines Powertrain Data Link Circuit - Test
12M Motor Grader Engine Starting
3406E, C-10 and C-12 On-highway Engines Multi-Torque - Test
3406E and 3456 Generator Set Engines Replacing the ECM
Product Link - PL102C Electrical Connector - Inspect
Product Link - PL102C Wiring Harness (Open Circuit) - Test
Product Link - PL102C Wiring Harness (Short Circuit) - Test
G3406 Engine Engine Operation
3406E, C-10 and C-12 On-highway Engines Injector Solenoid Circuit - Test
C11 and C13 Petroleum Engines Fan Drive
G3516B Engines ECM Status Indicator Output
12M Motor Grader Kingpin Bearings - Lubricate
3126B Petroleum Engine Connecting Rod
C27 PET GEN SET Electric Power Generation and C27 KNOCKDOWN K Petroleum Power Train Package Electrical System
3406E, C-10 and C-12 On-highway Engines PTO Switch Circuit - Test
C27 and C32 Industrial and Petroleum Engines Can Not Reach Top Engine RPM
C11 and C13 Engines Electronic Unit Injector Wiring
143H and 163H Motor Graders Wheel Bearing Oil (Front) - Change - If Equipped
143H and 163H Motor Graders Wheel Bearing Oil Level (Front) - Check - If Equipped
C-10, C-12, C-15 and C-16 Industrial Engines Intermittent Low Power or Power Cutout
C-10, C-12, C-15 and C-16 Industrial Engines Low Power/Poor or No Response to Throttle
3406E and 3456 Generator Set Engines CID 0336 FMI 02 Incorrect ECS Switch inputs
3406E and 3456 Generator Set Engines CID 0337 FMI 02 Incorrect Remote E-Stop Switch inputs
C11 and C13 Engines Fuel Filter Base