Housing (Front) - Install
Show/hide table
Required Tools | |||
---|---|---|---|
Tool | Part Number | Part Description | Qty |
A | 8T-9022 | Silicone Gasket | - |
Show/hide table
NOTICE |
---|
Keep all parts clean from contaminants. Contaminants may cause rapid wear and shortened component life. |
Show/hide table
NOTICE |
---|
Do not turn the crankshaft or the camshaft while the camshaft gear is removed. If the front gear group is not correctly timed during installation, interference can occur between the pistons and the valves, resulting in damage to the engine. |
- Thoroughly clean the mating surfaces of the plate (18) and the front housing (15).
- Install a new gasket (17) on plate (18).
Note: Trim the gasket even with the bottom of the front housing after assembly.
- Apply Tooling (A) to the bottom of gasket (17) in order to fill the space at the front housing and the engine oil pan.
- Install front housing (15) on the dowel pins on the cylinder block.
- Install bolts (19) for the engine oil pan to a torque of
55 ± 10 N·m (41 ± 7 lb ft) .Show/hide tableIllustration 2 g01067631 - Install bolts (16) in front housing (15).
- Install bolt (12).
- Install the nut on stud (11).
- Install bolts (13) and nuts (14) on the front housing.
- Position strap (10) on the front housing and on the cylinder head and install bolts (9).
Show/hide table
Illustration 3 g01067632 - Position bracket (4) and install bolts (3).
- Position clips (1) and (5) and install bolts (2).
- Install bolts (6).
- Position plate (8) on the studs. Install nuts (7) and the washer on the studs.
- If necessary, install the accessory drive on the front housing.
Show/hide table
Illustration 1 | g01067633 |
End By:
- Install the crankshaft position sensor. Refer to Disassembly and Assembly, "Crankshaft Position Sensor - Remove and Install".
- Install the camshaft position sensor. Refer to Disassembly and Assembly, "Camshaft Position Sensor - Remove and Install".
- Install the auxiliary water pump, if necessary. Refer to Disassembly and Assembly, "Auxiliary Water Pump - Install".
- Install the pump drive, if necessary. Refer to Disassembly and Assembly, "Pump Drive - Install".
- Install the crankshaft front seal and the wear sleeve. Refer to Disassembly and Assembly, "Crankshaft Front Seal - Install".
- Install the camshaft gear. Refer to Disassembly and Assembly, "Camshaft Gear - Remove and Install".
- Install the air compressor, if necessary. Refer to Disassembly and Assembly, "Air Compressor - Remove and Install".
Caterpillar Information System:
C15 Petroleum Engines Housing (Front) - Remove
C15 Industrial Engines Plate Locations and Film Locations
C15 Industrial Engines Model View Illustrations
3406E and 3456 Generator Set Engines Electrical Power Supply Circuit - Test
C15 Industrial Engines Safety Messages
Product Link - PL102C Operating Hours Discrepancy
3406E and 3456 Generator Set Engines Engine Control Switch (ECS) (EMCP II)
2004/04/01 A New Special Instruction, REHS1531, "Oxidation Catalyst Converter for Stationary Engines" is Available {1091}
3126B Petroleum Engine Injection Actuation Pressure Sensor - Test
2004/09/06 Correction to Service Magazine "Hydraulically Fractured Connecting Rods are Now In Production" {1218}
2004/06/01 A New Piston Pin Retainer is Used {1214}
C27 and C32 Engines for Caterpillar Built Machines Cylinder Head
12M Motor Grader Backup Alarm - Test
12M Motor Grader Blade Lift Cylinder Socket - Lubricate
12M Motor Grader Blade Lift Cylinder Socket - Check/Adjust/Replace
C11 and C13 Petroleum Engines Plate Locations and Film Locations
C15 Engine Reference Material
Product Link - PL102C Reports and Messages Not Available
3406E and 3456 Generator Set Engines Air Shutoff System - Test
3508, 3512, and 3516 Generator Sets Refill Capacities and Recommendations
Machining of The Cylinder Block to Convert from Wet Cylinder Liners to Dry Cylinders Liners{1201} Machining of The Cylinder Block to Convert from Wet Cylinder Liners to Dry Cylinders Liners{1201}
C15 Petroleum Engines Pump Drive - Remove
C15 Petroleum Engines Pump Drive - Install
3406E and 3456 Generator Set Engines Emergency Stop Switch Circuit - Test