Flywheel Adapter - Remove and Install
Show/hide table
所需工具 | |||
---|---|---|---|
工具 | 零件号 | 零件说明 | 数量 |
A | 138-7573 | 提升支架 | 2 |
B | - | 导向螺柱 (5/8 - 18 x 8 in) |
2 |
C | 9S-9082 | 发动机盘车工具 | 1 |
开始:
- 拆下电起动马达。 请参阅拆解和组装 , "电起动马达 - 拆卸"。
Show/hide table
注意 |
---|
保持所有零件清洁无杂质。 杂质会造成快速磨损和缩短部件寿命。 |
- 拆下螺塞 (3)。 使用工具 (C) 转动飞轮,以便通过飞轮壳体 ( 1) 拆下螺栓 (6)。 拆下螺栓 (6)。
- 拆下密封垫 (7)。
- 从飞轮壳体 (2) 上拆下密封垫 ( 8) 和飞轮壳体适配器 ( 1)。
- 拆下螺栓 (5),然后从飞轮上拆下柔性板 ( 4)。
Show/hide table
图 2 g01065196 - 将工具 (A) 安装到飞轮 ( 10) 上。 使用适当的提升装置。 飞轮 (10) 的重量约为
35 kg (77 lb) 。 - 拆下两个螺栓 (9)。 安装工具 (B)。
- 拆下剩余的螺栓 ( 9)。 拆下飞轮 (10)。
Show/hide table
图 3 g01065195 - 使用锤子和冲头以将导向衬套 ( 12) 从飞轮 (10) 上拆下。
- 使用锤子和冲头以将齿圈 ( 11) 从飞轮 (10) 上拆下。
Show/hide table
图 1 | g01065202 |
Show/hide table
所需工具 | |||
---|---|---|---|
工具 | 零件号 | 零件说明 | 数量 |
A | 138-7573 | 提升支架 | 2 |
B | - | 导向螺柱 (5/8 - 18 x 8 in) |
2 |
C | 9S-9082 | 发动机盘车工具 | 1 |
D | 1P-0510 | 冲头总成 | 1 |
E | - | 导向螺柱 (1/2 - 20 x 4 in) |
1 |
Show/hide table
注意 |
---|
保持所有零件清洁无杂质。 杂质会造成快速磨损和缩短部件寿命。 |
- 将齿圈 (11) 加热到
316 °C (600 °F) 的最高温度。 将齿圈 (11) 安装在飞轮 ( 10) 上。 - 使用工具 (D) 将导线衬套 ( 12) 安装到飞轮 (10) 中。
Show/hide table
图 5 g01065196 - 将工具 (B) 安装在曲轴中。
- 将工具 (A) 安装到飞轮 ( 10) 上。 使用适当的提升装置。 飞轮 (10) 的重量约为
35 kg (77 lb) 。 将飞轮 (10) 定位到曲轴上。 - 将清洁的发动机机油涂抹在螺栓 ( 9) 的螺纹上。
- 安装螺栓 (9)。 拆下工具 (B)。 将螺栓 ( 9) 安装在工具 (B) 的位置上。
- 拧紧螺栓 (9) 至扭矩为
272 ± 27 N·m (200 ± 20 lb ft) 。 - 从飞轮 (10) 上拆下工具 ( A)。
- 检查飞轮跳动。 请参阅测试与调整 , "飞轮 - 检查" 。
Show/hide table
图 6 g01065202 - 将柔性板 (4) 放置到位,然后安装螺栓 ( 5)。 拧紧螺栓 (5) 至扭矩为
143 ± 13 N·m (105 ± 10 lb ft) 。 - 将密封垫 (8)、飞轮壳体适配器 ( 1) 和密封垫 (7) 安装到飞轮壳体 ( 2) 中。
- 将工具 (E) 对准柔性板 ( 4)、飞轮 (10) 和飞轮壳体 ( 2)。
- 拆下工具 (E),然后安装螺栓 ( 6)。 将螺栓 (6) 上紧到
143 ± 13 N·m (105 ± 10 lb ft) 的扭矩。 - 使用工具 (C) 转动飞轮 ( 10),以便通过飞轮壳体 ( 2) 安装剩余螺栓 (6)。 拧紧螺栓 (6) 至扭矩为
143 ± 13 N·m (105 ± 10 lb ft) 。 - 将螺塞 (3) 安装到飞轮壳体 ( 2) 中。
Show/hide table
图 4 | g01065195 |
注: 安装齿圈 (11) 的时候必须让轮齿斜面一侧朝上。 当飞轮 (10) 安装完毕之后,轮齿斜面一侧应朝向起动马达。
结束:
- 安装电起动马达。 请参阅拆解和组装 , "电起动马达 - 拆卸和安装" 。
Caterpillar Information System:
C18 Industrial Engines Plate Locations and Film Locations
C15 Petroleum Engines Flywheel - Install
C15 Petroleum Engines Flywheel - Remove
C-15 Petroleum Engine Cooling System - Check - Overheating
G3520C and G3520E Generator Set Engines Auxiliary Water Pump - Assemble
G3520C and G3520E Generator Set Engines Auxiliary Water Pump - Disassemble
G3516B Engines MID 036 - CID 1719 - FMI 04 Generator Output Power Sensor short to ground
G3516B Engines MID 036 - CID 1719 - FMI 03 Generator Output Power Sensor open/short to +batt
3406E, C-10 and C-12 On-highway Engines Check Engine Lamp Circuit - Test
3406E, C-10 and C-12 On-highway Engines Engine Shutdown Output Circuit - Test
2005/04/01 New Injectors and New Flash Files are Now in Production. {1290, 7620}
C15 Petroleum Engines Electronic Control Module - Remove and Install
3126B Marine Engines Analog Sensor Supply Circuit - Test
C-15 Petroleum Engine Vibration Damper - Check
C18 Generator Set Safety Messages
3406E and 3456 Generator Set Engines Analog Sensor Supply Circuit - Test
3406E and 3456 Generator Set Engines CAT Data Link Circuit - Test
2004/05/01 Procedure to Allow Clearance to Install an Eaton VCTplus Clutch {1156}
G3520C and G3520E Generator Set Engines Generator Output Power Readings Do Not Match
3406E and 3456 Generator Set Engines Digital Sensor Supply Circuit - Test
3126B Petroleum Engine Intermittent Engine Shutdown
C15 Petroleum Engines Engine Oil Pump - Remove
C15 Petroleum Engines Engine Oil Pump - Install
Product Link - PL102C Service Tools