Air Lines - Remove and Install
Show/hide table
| NOTICE |
|---|
|
Keep all parts clean from contaminants. Contaminants may cause rapid wear and shortened component life. |
- Remove bolts (2) and the plates.
- Loosen hose clamps (4). Slide hose (5) onto tube assembly (1).
- Remove tube assembly (1) from turbocharger compressor housing (3). Remove the O-ring seals from the tube assembly.
- Remove bolt (8) and the retainer.
- Remove bolts (10) and the spacers from adapter (11).
- Remove pipe (7) from turbocharger compressor housing (9). Remove gasket (6) from the aftercooler.
- Remove bolts (12) and the retainers. Remove adapter (11) from pipe (7). Remove the O-ring seals from pipe (7).
Show/hide table
| |
| Illustration 1 | g01052465 |
Show/hide table
| Required Tools | |||
| Tool | Part Number | Part Description | Qty |
| A | 369-9451 | Grease | - |
Show/hide table
| NOTICE |
|---|
|
Keep all parts clean from contaminants. Contaminants may cause rapid wear and shortened component life. |
- Install the O-ring seals on pipe (7). Apply Tooling (A) to the O-ring seals. Install adapter (11) on pipe (7). Install the retainers and bolts (12). Do not tighten the bolts at this time.
- Install pipe (7) in turbocharger compressor housing (9). Install the retainer and bolt (8). Do not tighten the bolt at this time.
- Position gasket (6) between the aftercooler housing and adapter (11). Install the spacers and bolts (10).
- Tighten bolts (12) and bolt (8).
- Install the O-ring seals on tube assembly (1). Apply Tooling (A) to the O-ring seals. Install tube assembly (1) in turbocharger compressor housing (3). Install the plates and bolts (2). Do not tighten the bolts at this time.
- Align tube assembly (1) with pipe (7). Slide hose (5) onto pipe (7). Tighten hose clamps (4).
- Tighten bolts (2).
Show/hide table
|
| |
| Illustration 2 | g01052465 |
Caterpillar Information System:
G3500 Engines Electric Starting Motor - Test
EMCP3 Password Entry
C15 and C18 Engines for Caterpillar Built Machines E096 High Fuel Pressure
G3516B Engines Troubleshooting Data Sheet
C7 Marine Engine General Information
G3516C, G3516E, and G3512E Generator Set Engines Customer Passwords
C13, C15, and C18 Generator Set Engines Lubrication System
G3516B Engines Self-Diagnostics
G3516C, G3516E, and G3512E Generator Set Engines System Overview
C-15 Petroleum Engine Electronic Control System Components
3500B and 3500C Marine Engines Turbocharger
2004/03/01 An Improved Locknut for the Turbocharger Mounting Stud is Now Used {1052}
C7 Marine Engine Electronic Control System Components
G3500 Engines Air/Fuel Ratio Control - Adjust
2004/04/01 Replacement of the Injection Actuation Pressure Control Valve {5051}
3512B Generator Set Engine Turbocharger Exhaust Temperature Sensor
C18 Generator set and C18 Marine Engines Exhaust Elbow - Remove and Install
G3516B Engines Driven Equipment
3500C Marine Engines Aftercooler Coolant Temperature Sensor
C18 Generator set and C18 Marine Engines Water Lines - Remove and Install
G3516B Engines Engine Overload
C15 Engine Electronics Grounding Stud - Inspect/Clean/Tighten
G3516B Engines Engine Shutdown (Unexpected)
2004/03/01 Caterpillar Digital Voltage Regulator (CDVR) Is Now Being Used {4467}