Piston Cooling Jets - Remove and Install
拆卸步骤
开始:
- 拆卸发动机油底壳。 请参阅本解体和组装手册, "发动机油底壳 - 拆卸和安装"。
Show/hide table
注意 |
---|
保持所有零件清洁无杂质。 杂质会造成快速磨损和缩短部件寿命。 |
- 拆下调整螺钉 (1) 。 从缸体上拆下活塞冷却喷嘴组件 (2) 。
注: 为了靠近所有活塞冷却喷嘴组件,可能需要转动发动机曲轴。
Show/hide table
图 1 | g00952340 |
安装步骤
Show/hide table
注意 |
---|
保持所有零件清洁无杂质。 杂质会造成快速磨损和缩短部件寿命。 |
- 清洁每个活塞冷却喷嘴组件 (2) 。 检查各个组件是否损坏,尤其是检查并确认活塞冷却喷嘴组件 (2) 的管未损坏。 确保滚珠能在活塞冷却喷嘴 (2) 各个阀组件中移动自如。 更换所有损坏的组件。
Show/hide table
图 2 | g00952363 |
- 将各个活塞冷却喷嘴组件 (2) 装入缸体中。 安装调整螺钉 (1) 。 拧紧调整螺钉 (1) 到扭矩为 9 N·m (80 lb in)。
注: 确保活塞冷却喷嘴组件 (2) 在缸体上就位。 请参阅技术参数手册, "活塞冷却喷嘴",了解活塞冷却喷嘴定位的正确步骤。
End By: 安装发动机油底壳。 请参阅本 解体和组装手册, "发动机油底壳 - 拆卸和安装"。
Caterpillar Information System:
UPS 250, UPS 300, UPS 500, UPS 600, UPS 750 and UPS 900 Uninterruptible Power Supply Flywheel Telemetry - Calibrate - Flywheels with EVD Bearings
C9 Marine Engines and C9 Marine Generator Sets Crankshaft - Install
C9 Marine Engines and C9 Marine Generator Sets Crankshaft Main Bearings - Install
C9 Marine Engines and C9 Marine Generator Sets Crankshaft Main Bearings - Remove
C9 Marine Engines and C9 Marine Generator Sets Crankshaft - Remove
784C, 785C and 785C HAA Off-Highway Truck/Tractor Suspension Cylinder Pressure Sensor (Rear Suspension Cylinder)
3408C, 3412C and 3412D High Performance Marine Engines Piston and Rings
2003/10/01 New Fuel Check Valve {1262}
C9 Marine Engines and C9 Marine Generator Sets Inlet and Exhaust Valve Guides - Remove and Install
3408C, 3412C and 3412D High Performance Marine Engines Turbocharger
C9 Marine Engines and C9 Marine Generator Sets Inlet and Exhaust Valves - Remove and Install
C9 Marine Engines and C9 Marine Generator Sets Inlet and Exhaust Valve Seat Inserts - Remove and Install
3456 Generator Sets Safety Messages
3456 Generator Sets Cooling System Coolant Sample (Level 1) - Obtain
2003/11/01 Troubleshooting Guide for Marine Engine Cooling Systems is Now Available {1350}
3456 Generator Sets Cooling System Coolant Sample (Level 2) - Obtain
2003/11/01 Antifreeze is Added to the Corrosion Inhibitor {1395}
2003/11/01 Introduction of New Pistons and Remanufactured Cylinder Packs {1214, 1239}
3126B Industrial Engine Water Pump - Remove
2003/11/01 A New Seal and Oil Pan Provides Improved Sealing {1302, 1302}
3456 Generator Sets Maintenance Interval Schedule - Standby Generator Sets
3456 Generator Sets Maintenance Interval Schedule - Prime Power Generator Sets
2003/10/01 New Seals for the Front Housing {1151, 1207}
C3.3 Industrial Engine Bearing Clearance - Check