Inlet and Exhaust Valve Seat Inserts - Remove and Install
Removal Procedure
Show/hide table
Required Tools     | |||
Tool     | Part Number     | Part Description     | Qty     |
A     | 9S-3095     | Handle Assembly     | 1     |
B     | 9S-3098     | Hammer     | 1     |
C     | 173-5525     | Valve Seat Extractor     | 1     |
Start By:
- Remove intake and exhaust valves.
Show/hide table
NOTICE |
---|
Keep all parts clean from contaminants. Contaminants may cause rapid wear and shortened component life. |
- Install Tooling (C) in the inlet valve seat inserts and the exhaust valve seat inserts.
Show/hide table
Illustration 1 | g01109589 |
- Install Tooling (B) and Tooling (A) in Tooling (C) . Hand tighten Tooling (A) . Tooling (C) will expand below the edge of the valve seat inserts (1) .
- Slide Tooling (B) upward, in order to remove the valve seat inserts (1) .
Installation Procedure
Show/hide table
Required Tools     | |||
Tool     | Part Number     | Part Description     | Qty     |
D     | 173-5523     | Exhaust Valve Seat Driver     | 1     |
459-1075 | Intake Valve Seat Driver     | 1     |
Show/hide table
NOTICE |
---|
Keep all parts clean from contaminants. Contaminants may cause rapid wear and shortened component life. |
- Lower the temperature of the new valve seat inserts (1) . Use Tooling (D) to install the valve seat inserts into the cylinder head.
Show/hide table
Illustration 2 | g01109590 |
End By: Install the inlet valves and exhaust valves.
Caterpillar Information System:
120H and 135H Motor Graders Hydraulic and Steering System Metering Pump (Steering)
2003/11/01 New Gasket For The Cylinder Block Cover {1201}
C9 Marine Engines and C9 Marine Generator Sets Cylinder Liner - Remove
2003/11/01 New Expansion Tank Assembly {1354}
C3.3 Industrial Engine Camshaft - Remove and Install
C9 Marine Engines and C9 Marine Generator Sets Connecting Rod Bearings - Install
C9 Marine Engines and C9 Marine Generator Sets Connecting Rod Bearings - Remove
3408C, 3412, 3412C, and 3412D High Performance Marine Engines Safety Messages
2003/10/01 Proper Termination Techniques May Increase VR3 Voltage Regulator Reliability {1410}
C11 and C13 Petroleum Engines Speed/Timing Sensor
C9 Marine Engines and C9 Marine Generator Sets Pistons and Connecting Rods - Assemble
C9 Marine Engines and C9 Marine Generator Sets Pistons and Connecting Rods - Disassemble
C9 Marine Engines and C9 Marine Generator Sets Inlet and Exhaust Valves - Remove and Install
3408C, 3412C and 3412D High Performance Marine Engines Turbocharger
C9 Marine Engines and C9 Marine Generator Sets Inlet and Exhaust Valve Guides - Remove and Install
2003/10/01 New Fuel Check Valve {1262}
3408C, 3412C and 3412D High Performance Marine Engines Piston and Rings
784C, 785C and 785C HAA Off-Highway Truck/Tractor Suspension Cylinder Pressure Sensor (Rear Suspension Cylinder)
C9 Marine Engines and C9 Marine Generator Sets Crankshaft - Remove
C9 Marine Engines and C9 Marine Generator Sets Crankshaft Main Bearings - Remove
C9 Marine Engines and C9 Marine Generator Sets Crankshaft Main Bearings - Install
C9 Marine Engines and C9 Marine Generator Sets Crankshaft - Install
UPS 250, UPS 300, UPS 500, UPS 600, UPS 750 and UPS 900 Uninterruptible Power Supply Flywheel Telemetry - Calibrate - Flywheels with EVD Bearings
C3.3 Industrial Engine Piston Cooling Jets - Remove and Install