Poor Acceleration or Response
可能的根本原因按顺序列在下面:
- 诊断代码
- 进气门驱动系统
- 冷起动模式
- 客户指定参数(正常工作)
- 个别气缸故障
- 数据链路
- 扭矩限制开关
- 将卡特彼勒电子技师 (ET) 连接到数据链路接头上。
- 检查有无激活和/或记录的代码。 在继续进行本程序之前应对出现的任何代码进行故障诊断与排除。
注: 某些诊断代码可能会造成性能变差。
- 起动发动机。
- 监控卡特彼勒 ET 的状态屏幕。
- 注意在任一状态屏幕的左上角是否出现了一个 "进气门系统起动"的图标。
注: 在 "进气门系统起动"图标变为未激活之前发动机无法发出全部的动力。
- 起动发动机。
- 监控卡特彼勒 ET 的状态屏幕。
- 注意在任一状态屏幕的顶部是否出现了一个 "冷态模式"图标。
注: 在 "冷态模式"图标变为未激活之前发动机无法发出全部的动力。
- 核实投诉并不是正常工作(编程设定后的参数)。
- 进入卡特彼勒 ET 上的 "配置"屏幕。
- 检查下列参数:
- "低档位发动机转速限制"
- "中档位发动机转速限制"
- "减档保护发动机转速限制"
- "低档位发动机转速限制"
- 依次设定各个参数到最大值,确定是否排除该故障。
- 确保前、后气门室盖接头的连接充分而且没有腐蚀。
- 确保 J2/P2 ECM 接头的连接充分而且没有腐蚀。
- 使用"断缸测试"。 在 "诊断"菜单下面选择" 诊断测试",进入 "断缸测试"。 运行 "断缸测试"分别切断每个气缸。 停用各个喷油器可使技师隔离出缺火的气缸。
如果可以隔离缺火气缸为某一气缸,请参阅故障诊断与排除, "喷油器电磁阀电路 - 测试"。
- 确保传动系数据链路没有限制动力。
- 在车辆出现问题时监控 "传动系数据链路"状态屏幕。
如果 "传动系数据链路"状态屏幕显示"数据链路"正在限制动力或转速,确认这不是正常操作。 如果不是正常工作状态,请参阅车辆 OEM 进行修理。
- 检查客户参数"扭矩限制"的设定值。
如果 "扭矩限制"被设定为低于 3400 N (m)2500 lb ft,检查扭矩限制开关的状态屏幕。 确保状态屏幕显示的扭矩限制开关为 OFF。 如果扭矩限制开关的状态为 ON 并且设置过 "扭矩限制",系统工作正常。 如果与此信号输入相连的开关没有变为 ON 和 OFF,参见故障诊断与排除, "PTO 开关电路 - 测试".
Caterpillar Information System:
C11, C13 and C15 On-highway Engines Low Power/Poor or No Response to Throttle
C11, C13 and C15 On-highway Engines Intermittent Low Power or Power Cutout
C7 and C9 On-Highway Engines Engine Cranks but Will Not Start
3406E, C-10 and C-12 On-highway Engines Driver Questionnaire Response
C11, C13 and C15 On-highway Engines Engine Misfires, Runs Rough or Is Unstable
3126B and 3126E On-highway Engines ECM Will Not Accept Factory Passwords
3126B and 3126E On-highway Engines Can Not Reach Vehicle Speed Limit
3126B and 3126E On-highway Engines Can Not Reach Top Engine RPM
3406E, C-10 and C-12 On-highway Engines Excessive White Smoke
C11, C13 and C15 On-highway Engines Excessive Black Smoke
3044C Industrial Engine and Engines for Caterpillar Built Machines Engine Design
3500 Industrial Engines Stub Shaft (Front)
320B, 320B L and 320B N Excavators Cooling System Coolant Sample (Level 2) - Obtain
G3500B Engines Vibration Damper Guard
EMCPII+ for Gas Engines Hourmeter Programming OP7
3044C Industrial Engine and Engines for Caterpillar Built Machines General Information
3044C Industrial Engine and Engines for Caterpillar Built Machines Fuel Injection Lines
EMCPII+ for Gas Engines Electronic Ignition System
3044C Industrial Engine and Engines for Caterpillar Built Machines Rocker Shaft
EMCPII+ for Gas Engines Starting Motor Magnetic Switch - Test - for Engine with ECM
EMCPII+ for Gas Engines Starting Motor Magnetic Switch - Test - for Engine with EIS
C15 On-highway Engine Variable Valve Actuator Oil Pressure Sensor
C15 On-highway Engine Variable Valve Actuator
3406E, C-10, C-12, C-15, C-16 and C-18 On-highway Engines Coolant Level Sensor Circuit - Test