Fuel System Pressure - Test
技术规格
Show/hide table
燃油系统压力技术规格     | |
燃油流量     | 2 L/min (0.53 US gpm)     |
怠速时的燃油压力     | 25 kPa (3.63 psi)     |
高怠速时的燃油压力     | 25 kPa (3.63 psi)     |
喷油泵最大压力     | 75 kPa (10.88 psi)     |
简介
以下步骤用于检查燃油系统压力。 压力测试测量燃油注油泵的输出压力。 燃油压力低以及难以起动可能表明输油泵有问题。
测试步骤
Show/hide table
图 1 | g00928705 |
(A 和 B) 出油口 (1) 燃油注油泵 (2) 燃料滤清器 |
检查燃油注油泵的功能
- 记录燃油注油泵出来的燃油管的位置。 从出口 (A) 和 (B) 上卸下两个油管。
- 将两个长度为 5/16 in 的橡胶软管连接到出口 (A) 和 (B) 上。 将软管放入能盛放 3 L (3.17 qt) 燃油的适当容器中。
- 通电燃油注油泵,直到喷油泵供油出口流出恒流燃油。
注: 燃油箱回油出口流出燃油的流量较低。
- 使用秒表测量两个出口的组合流量。 燃油流量至少应为 2 L/min (0.53 US gpm)。
- 如果组合流量小于 2 L/min (0.53 US gpm),则需修理或更换油泵。
- 重新将出口油管连接到位。
- 起动发动机,检查燃油管中有无燃油或空气泄漏。
检查压力调节器的功能
- 从喷油泵 (B) 供油出口卸下燃油管。
- 安装一条有压力表测压孔的油管。 连接一个 0 至 80 kPa (0 至 12 psi) 压力表。
- 起动发动机,在怠速转速下运转发动机两分钟来清除所有困气。
- 记录怠速和高怠速下的压力读数。 压力读数应为以下数值:
所有喷油泵
- 怠速 ... 25 kPa (3.63 psi)
- 高怠速 ... 25 kPa (3.63 psi)
注: 喷油泵的最大压力为 75 kPa (10.88 psi)。
- 将钥匙开关转到运转位置保持三分钟,使注油泵通电。 不要起动发动机。 然后将钥匙开关转到断开位置。
- 如果压力不符合上述技术参数,检查有无下列问题。
- 正确安装所有电气接头。
- 燃油管或接头中没有泄漏。
- 燃油滤清器壳体 (2) 上的 O 形密封圈没有泄漏。
- 正确安装所有电气接头。
Caterpillar Information System:
3054C Industrial Engine and C4.4 Marine Auxiliary Generator Set Fuel System - Prime
C9 Marine Generator Set Engines Engine Oil Pressure - Test
3056E Industrial Engine Crankshaft Main Bearings - Install
3056E Industrial Engine Crankshaft - Install
3056E Industrial Engine Crankshaft - Remove
G3406 and G3412 Generator Set Engines Ignition Transformer
C9 Marine Generator Set Engines Inlet Manifold Pressure - Test
C4.4 (Mech) Industrial Engine Cylinder Head - Inspect
C9 Marine Generator Set Engines Turbocharger - Inspect
G3406 and G3412 Generator Set Engines Spark Plug and Transformer - 11.4:1 Compression Ratio
G3408C and G3412C Engines Gas Pressure Regulator
3054E Industrial Engine Power Sources
3406E and C15 Marine Engines Cooling System - Check - Overheating
3056E Industrial Engine Crankshaft Main Bearings - Remove
3056E Industrial Engine Piston Cooling Jets - Remove and Install
3054E Industrial Engine Camshaft Bearings - Remove and Install
C7 and C9 On-Highway Engines 0232-03 5 Volt Supply voltage high (21)
C7 and C9 On-Highway Engines 0232-04 5 Volt Supply voltage low (21)
Test Sequence for Capsule Type Fuel Nozzles{0782} Test Sequence for Capsule Type Fuel Nozzles{0782}
C7 and C9 On-Highway Engines ATA (SAE J1587 / J1708) Data Link Circuit - Test
2002/10/28 Examine Failed Starting Motors to Understand the Reason for Failure {1453}
C7 and C9 On-Highway Engines Check Engine Lamp Circuit - Test
C15 Petroleum Generator Set Engines Electric Starting Motor
C7 On-highway Engine Piston and Rings