Evaporator Coil - Remove and Install
Start By:
a. Remove the heating and air conditioning unit.
Note: Cleanliness is an important factor. Before the disassembly procedure, the exterior of the component should be thoroughly cleaned to prevent dirt from entering the internal mechanism.
- Disconnect harness assemblies (1) and (2).
Show/hide table
Illustration 2 g01187598 - Remove bolts (3).
Show/hide table
Illustration 3 g01187599 - Separate case (4) from case (5).
Show/hide table
Illustration 4 g01187620 - Remove temperature sensor (6).
- Remove evaporator coil (7).
Show/hide table
Illustration 1 | g01187597 |
Note: Cleanliness is an important factor. Before assembly, all parts should be thoroughly cleaned in cleaning fluid. Allow the parts to air dry. Wiping cloths or rags should not be used to dry parts. Lint may be deposited on the parts which may cause later trouble. Inspect all parts. If any parts are worn or damaged, use new parts for replacement.
- Install evaporator coil (7).
- Install temperature sensor (6).
Show/hide table
Illustration 6 g01187599 - Connect case (4) to case (5).
Show/hide table
Illustration 7 g01187598 - Install bolts (3).
Show/hide table
Illustration 8 g01187597 - Connect harness assemblies (1) and (2).
End By:
a. Install the heating and air conditioning unit.
Show/hide table
Illustration 5 | g01187620 |
Caterpillar Information System:
336D 2L and 340D 2L Excavators Machine Systems Heater Core - Remove and Install
336D 2L and 340D 2L Excavators Machine Systems Heating and Air Conditioning Unit - Remove and Install
336D 2L and 340D 2L Excavators Machine Systems Swing Gear and Bearing - Remove and Install
PM620, PM622, PM820 and PM822 and PM825 Cold Planer Machine Systems Steering Control Group
301.7D CR Mini Hydraulic Excavator Track Adjustment - Inspect
PM620, PM622, PM820 and PM822 and PM825 Cold Planer Machine Systems Control Valve and Mounting
CB7, CB8 and CB10 Vibratory Asphalt Compactors Machine Systems Hydraulic Cylinder (Offset)
PM620, PM622, PM820 and PM822 and PM825 Cold Planer Machine Systems Check Valve
745 and 740 GC & 740 EJECTOR Articulated Truck Systems Check Valve
PM620, PM622, PM820 and PM822 and PM825 Cold Planer Machine Systems Track Roller (Single Flange)
PM620, PM622, PM820 and PM822 and PM825 Cold Planer Machine Systems Electronic Control Module
PM620, PM622, PM820 and PM822 and PM825 Cold Planer Machine Systems Conveyor System
C18 Generator Set Engines DEF Injector and Mounting - Remove and Install
C18 Generator Set Engines Manifold (DEF Heater) - Remove and Install
336D 2L and 340D 2L Excavators Machine Systems Cab - Remove and Install
336D 2L and 340D 2L Excavators Machine Systems Fuel Tank - Remove and Install
New Engine Software is Available for Certain C7.1 Machine Engines {7610, 7620} New Engine Software is Available for Certain C7.1 Machine Engines {7610, 7620}
C2.4 Tier 4 Final Engines for Caterpillar Built Machines Electric Starting Motor - Remove and Install
352F Mobile Hydraulic Power Unit (MHPU) Machine System Main Hydraulic System
336D 2L and 340D 2L Excavators Machine Systems Hydraulic Lockout Control - Remove and Install
336D 2L and 340D 2L Excavators Machine Systems Window Wiper Motor - Remove and Install - Lower
GSH420, GSH425, GSH440, GSH520, GSH525, GSH455 and GSH555 Orange Peel Grapples Head Assembly and Bushing - Remove and Install
C18 Generator Set Engines Voltage Control (Load Protection) - Remove and Install
349F and 352F Excavators Joystick Controls - Cat Grade With Assist System