3126 Truck Engine (Military) Caterpillar


Maintenance Interval Schedule

Usage:

3126 1BW
Note: Ensure that the Safety Information, warnings, and instructions are read and understood before operation or maintenance procedures are performed.

Note: Use distance (odometer), fuel consumption, service hours, or calendar time, whichever occurs first , in order to determine the maintenance intervals. Engines that operate in severe operating conditions may require more frequent maintenance.

Before each consecutive interval is performed, all of the maintenance requirements from the previous interval must also be performed.

When Required

Battery - Replace
Battery or Battery Cable - Disconnect
Engine Storage Procedure - Check
Fuel System - Prime
Severe Service Application - Check

Daily

Cooling System Coolant Level - Check
Engine Air Cleaner Service Indicator - Inspect
Engine Oil Level - Check
Fuel System Water Separator - Drain
Walk-Around Inspection

Initial 17 700 km (11 000 miles) or 4150 L (1100 US gal) of Fuel or 250 Service Hours or 6 Months

Engine Valve Lash - Inspect/Adjust

PM Level 1 - Every 17 700 km (11 000 miles) or 4150 L (1100 US gal) of Fuel or 250 Service Hours or 6 Months

Aftercooler Core - Inspect
Battery Electrolyte Level - Check
Cooling System Supplemental Coolant Additive (SCA) - Test/Add
Cylinder Head Grounding Stud - Inspect/Clean/Tighten
Engine Crankcase Breather - Clean
Engine Oil Sample - Obtain
Engine Oil and Filter - Change
Fan Drive Bearing - Lubricate
Fuel System Primary Filter - Clean/Replace
Fuel System Secondary Filter - Replace
Fuel Tank Water and Sediment - Drain
Hoses and Clamps - Inspect/Replace
Radiator - Clean

PM Level 2 - Every 161 000 km (100 000 miles) or 56 850 L (15 000 US gal) of Fuel or 2000 Service Hours or 2 Years

Aftercooler Core - Clean/Test
Air Compressor - Inspect
Alternator - Inspect
Belt Tensioner - Inspect
Cooling System Water Temperature Regulator - Replace
Crankshaft Vibration Damper - Inspect
Engine - Clean
Engine Air Cleaner Element - Clean/Replace
Engine Mounts - Inspect
Engine Valve Lash - Inspect/Adjust
Starting Motor - Inspect
Turbocharger - Inspect
Water Pump - Inspect

Every 6 Years or 966 000 km (600 000 miles)

Cooling System Coolant (ELC) - Change

Every 483 000 km (300 000 miles) or 3 Years

Cooling System Coolant (DEAC) - Change
Cooling System Coolant Extender (ELC) - Add

Every 114 000 L (30 000 US gal) of Fuel

Overhaul Considerations

Caterpillar Information System:

3126 Truck Engine (Military) Engine Operation
3054 and 3056 Engines 520 Generator Set Control Panel Initial Startup Procedure
Power Module Switchgear (Low Voltage and Medium Voltage) Generator Circuit Breaker
3054 and 3056 Engines 520 Generator Set Control Panel Specification
3054 and 3056 Marine Generator Set Engines Valve Depth - Inspect
3054 and 3056 Engines 520 Generator Set Control Panel Symbols
3126 Truck Engine (Military) Diagnostic Flash Code Retrieval
2001/11/01 Setting the Desired Rated Speed or Emissions Strategy for Generator Sets {1901}
Power Module Switchgear (Low Voltage and Medium Voltage) Manual Parallel Operation
3406E, C-10, C-12, C-15, C-16 and C-18 On-highway Engines Air Inlet Shutoff Circuit - Test
120H, 12H, 135H, 140H, 143H, 160H and 163H Motor Graders Electrical Connector - Inspect
Power Module Switchgear (Low Voltage and Medium Voltage) Base Load Operation
3126 Truck Engine (Military) Engine Oil and Filter - Change
3054 and 3056 Marine Generator Set Engines Air Inlet Heater - Test
UPS 250, UPS 300, UPS 500, UPS 600, UPS 750 and UPS 900 Uninterruptible Power Supply Dry Contact - Configure
SCT673 Truck Mounted PumperPOD Control Panel - Raise/Lower Blender
3126E Truck Engine Turbocharger
3116 Truck Engine Exhaust Brake
3054 and 3056 Marine Generator Set Engines Alternator - Test
3408E and 3412E Industrial Engines Cylinder Block
3116 Truck Engine Gear Group - Inspect
325D and 329D Excavators and 325D Material Handler Machine System Specifications Handle Control (Travel)
3126 Truck Engine (Military) Reference Material
C27 and C32 Engines for Caterpillar Built Machines System Overview
Back to top
The names Caterpillar, John Deere, JD, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
CH-Part.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only.