Auxiliary Water Pump - Disassemble - Rubber Impeller
拆解步骤
Show/hide table
| 所需工具 | |||
| 工具 | 零件号 | 零件描述 | 数量 |
| A | 1P-2321 | 拉拔器总成 | 1 |
| B | 1P-1861 | 挡圈钳 | 1 |
| C | 1P-1859 | 挡圈钳 | 1 |
| D | 1P-1855 | 挡圈钳 | 1 |
| E | 8H-0663 | 轴承拉拔器总成 | 1 |
开始:
- 拆卸辅助水泵。 参考拆解与组装, "辅助水泵 - 拆卸"。
Show/hide table
| 注意 |
|---|
保持所有零件清洁无杂质。 杂质会造成快速磨损和缩短部件寿命。 |
Show/hide table
| 注意 |
|---|
在检验、保养、测试、调整及维修产品时，务必留心，确保液体盛装在容器中。 在打开任何腔室或拆解任何储有液体的部件之前，要准备好用合适的容器收集液体。 有关适合收集和盛接卡特彼勒产品上液体的工具及用品，参考专门出版物, NENG2500, "卡特彼勒工具和修理车间设备指南"。 按照当地法规和指令处置所有液体。 |
- 使用工具 (A) 拆下主动齿轮 (1) 。
Show/hide table
 | |
| 图 1 | g01028588 |
- 使用工具 (C) 拆下挡圈 (2) 。
- 拆下隔套 (3) 。
- 拆下盖 (20) 。
- 拆下叶轮 (19) 。
- 拆下凸轮衬套 (18) 。
- 使用工具 (B) 拆下挡圈 (16) 。
- 拆下板 (17) 。
- 分离壳体 (4) 与壳体 (15) 。
- 使用适当的压力机从壳体 (4) 上拆下轴组件 (10) 。
- 使用适当的压力机和工具 (E) 拆下轴承 (6) 。
- 使用工具 (D) 拆下挡圈 (7) 。
- 使用适当的压力机和工具 (E) 从轴组件 (10) 上拆下轴承 (9) 和隔套 (8) 。
- 从轴组件 (10) 上拆下垫圈 (14) 。
- 从轴组件 (10) 上拆下密封件 (13) 和 (12) 。
- 从轴组件 (10) 上拆下垫圈 (11) 。
- 从壳体 (4) 上拆下密封件 (5) 。
Caterpillar Information System:
SR4 Generator with VR3 or VR4 Voltage Regulator General Information
Installation and Removal Of The Mechanically Attached Wear Plate System Installation and Removal Of The Mechanically Attached Wear Plate System
SR4 Generator with VR3 or VR4 Voltage Regulator Glossary
G3408C and G3412C Engines Ignition Transformer
2001/10/01 New Piston Assemblies Are Used {1214}
Operating Instructions for the 4P-4788 Electrical Converter Gp and the 4P-4789 Electrical Converter Gp {1421} Operating Instructions for the 4P-4788 Electrical Converter Gp and the 4P-4789 Electrical Converter Gp {1421}
Power Module Switchgear (Low Voltage and Medium Voltage) Burn Prevention
Power Module Switchgear (Low Voltage and Medium Voltage) Engine Stopping
Power Module Switchgear (Low Voltage and Medium Voltage) Engine Starting
Power Module Switchgear (Low Voltage and Medium Voltage) Before Starting Engine
3114, 3116, and 3126 Industrial and Generator Set Engines Fan Drive Bearing - Lubricate - If Equipped
3056E Industrial Engine Camshaft Bearings
C27 and C32 Engines for Caterpillar Built Machines CID 1589 FMI 03 Turbo Inlet Air Pressure Sensor open/shrt to +bat
C1.1, C1.5 and C2.2 Engines for Caterpillar Built Machines Engine Oil Pressure Switch - Remove and Install
C0.5, C0.7, C1.1/3011C, C1.5/3013C, C1.6 and C2.2/3024C/3024CT Industrial Engines and Engines for Caterpillar Built Machines Glow Plugs - Remove and Install
3126B Marine Engines CID 0105 FMI 03 Inlet Manifold Temp Sensor open/short to +batt
Automatic Transfer Switches CTG, CTGD Series Exerciser
3126B Marine Engines CID 0105 FMI 04 Inlet Manifold Temp Sensor short to ground
SCT673 Truck Mounted PumperPOD Junction Box
SR4 Generator with VR3 or VR4 Voltage Regulator Component Descriptions
3054 and 3056 Marine Generator Sets Stopping the Engine
SR4 Generator with VR3 or VR4 Voltage Regulator Generator Operation
3408E and 3412E Industrial Engines Engine Sensor Open/Short Circuit - Test
3408E and 3412E Industrial Engines E017 High Engine Coolant Temperature Warning