Pilot System Pressure - Test
Show/hide table
在发动机停机后,液压系统或动力传动系的部件中将会依然存在高压下的热液压油。 液压油的未受控制的释放可能会导致机器的突然移动或造成以下情况:
如果液压油穿透人体组织,必须立刻找熟悉这类创伤的医生来治疗。 请使用木板或硬纸板來检查液压油泄漏情况。 确保所有附件都已经降至地面上并且液压系统和动力传动系中的所有截留的压力都已经得到了释放。 此外,在拆卸任何部件或管路前,要确保液压油是冷的。 只有当发动机停机,而且加注口盖足够冷却,可以直接用手接触时,才可以拆卸液压油加注口盖。 |
Show/hide table
机器的突然移动或意外起动会对机器上或附近的人员造成人身伤亡。 为了防止人身伤亡,进行以下操作: 将机器放在光滑、水平的表面上。 将作业机具降至地面,并接合停车制动器。 停止发动机,拔下钥匙。 锁止车轮并安装转向机架锁。 |
Show/hide table
注意 |
---|
在进行检验、保养、测试、调整及维修产品期间,必须小心以确保装好排放出的油液。 在打开任何舱室或解体任何储有液体的部件之前,要准备好合适的容器收集液体。 有关收集和盛接 Cat 产品上油液的适用工具和用品,请参阅专门出版物, NENG2500, "代理商维修工具目录"。 按照当地法规和要求处置所有液体。 |
技术规格
Show/hide table
先导和制动压力 - 高怠速     | |
3500 kPa (510 psi)     |
|
简介
由机具泵提供先导和制动压力。 由先导歧管内的减压阀控制先导压力,该歧管位于反铲机具阀内部。
所需工具
Show/hide table
图 1 | g02571852 |
工具 (A) 198-4240 数字压力指示器总成 |
Show/hide table
所需工具     | ||||
---|---|---|---|---|
工具     | 项目     | 数量     | 零件号     | 说明     |
A     |     | 198-4240     | 数字压力指示器总成     | |
    | A1     | 1     | 198-4234     | 数字指示器     |
A2 | 1     | 198-4239     | 压力传感器总成 (0 至 41368 kPa(0 至 6000 psi))     |
|
A3 | 1     | 198-4236     | 适配器缆线组件     |
检查准备工作
- 将机器移至远离其他工作机器和人员的光滑、水平的位置。
- 将变速箱方向移到空档位置。
- 接合停车制动器。
- 将装载机和反铲降至地面。
- 停止发动机。
- 释放液压系统的压力。
参考有关释放液压压力的更多信息,请参阅维修手册模块测试和调整, "系统压力 - 释放"。
检查程序
- 将工具 (A) 安装到测试口 (2) 。
Show/hide table
图 2 | g03749444 |
机器底部视图。 (1) 先导歧管 (2) 先导压力测试端口 |
- 起动机器。
- 升高发动机转速至高怠速。
- 观察工具 (A) 上的先导压力,压力应为 3500 kPa (510 psi)。
- 将发动机转速降到低怠速。
- 停止发动机。
- 拆下工具 (A) 。
检查完成。
Caterpillar Information System:
Procedure to Install 432-6064 Quick Coupler Lines Gp on Certain Backhoe Loaders {5057, 6129} Procedure to Install 432-6064 Quick Coupler Lines Gp on Certain Backhoe Loaders {5057, 6129}
308E Mini Hydraulic Excavator Machine Systems Boom Cylinder - Remove and Install
320D2, 323D2, 326D2, 329D2 and 330D2 Excavators Tool Control System System 3 Prime: Relief Valve (Line) - Test and Adjust - Tool Relief Valve
Quick Coupler Installation Status{7610, 7620} Quick Coupler Installation Status{7610, 7620}
320D2, 323D2, 326D2, 329D2 and 330D2 Excavators Tool Control System System 3 Prime: Relief Valve (Line) - Test and Adjust - Auxiliary Control Valve
415F2, 416F2, 420F2 IT, 420F2 ST, 430F2 IT and 430F2 ST Backhoe Loaders Power Train Axle Housing and Flange - Remove
320D2 Forest Machine Machine System Specifications Control Valve
320D2, 323D2, 326D2, 329D2 and 330D2 Excavators Tool Control System System 3 Prime: Default Value of Work Tool Parameters
320D2 Forest Machine Machine System Specifications Cab Riser Wiring
320D2 Forest Machine Machine System Specifications Cab Riser Wiring
320D2 Forest Machine Machine System Specifications Boom Lighting
320D2 Forest Machine Machine System Specifications Fuel Tank
415F2, 416F2, 420F2 IT, 420F2 ST, 430F2 IT and 430F2 ST Backhoe Loaders Power Train Axle Housing and Flange - Disassemble
415F2, 416F2, 420F2 IT, 420F2 ST, 430F2 IT and 430F2 ST Backhoe Loaders Power Train Axle Housing and Flange - Assemble
308E Mini Hydraulic Excavator Machine Systems Bucket Linkage - Remove and Install
2014/11/19 An Improved Welding Process for the Bucket Hinge Plate is Used on Certain 336D, 336D2, and 340D Excavators {6001}
2014/12/05 An Improved Process Is Used To Install Water Ferrule Inserts In All 3500 Engines {0705, 1201, 1217}
2014/12/05 An Improved Process Is Used To Install Water Ferrule Inserts In All 3500 Machine Engines {0705, 1201, 1217}
320D2, 323D2, 326D2, 329D2 and 330D2 Excavators Tool Control System Solenoid Valve (Proportional Reducing) - Calibrate - Negative Flow Control
320D2 Forest Machine Machine System Specifications Pilot Lines
320D2 Forest Machine Machine System Specifications Relief Valve (Line)
320D2 Forest Machine Machine System Specifications Fuel Lines
568 Forest Machine Machine System Specifications Heater and Air Conditioner Mounting
320D2 Forest Machine Circuit Breakers - Reset