Engine and Machine Warm-Up
Show/hide table
注意事項 |
---|
保持引擎低速,直到計量儀器上標示出引擎油壓,或是引擎油指示燈熄滅。 如在十秒鐘內燈未熄滅或未標示油壓,則停止引擎並在重新啟動前調查原因。 未能如此操作可導致引擎損壞。 |
附註在液壓控制裝置開始作用前,必須將液壓鎖定控制裝置調至 LOWERED (取消鎖定) 位置。
- 在低怠速下,讓引擎預熱 5 分鐘。 嚙合作業機具控制的操縱桿,然後脫離作業機具控制的操縱桿。 此方法可加速預熱液壓組件。 如果溫度低,或是液壓功能的效率低落,可能需要增加作業時間。
- 請將引擎速度轉盤轉至中等引擎速度,開始預熱液壓油。 運轉引擎約 5 分鐘,然後將操縱桿間歇地從 BUCKET DUMP (鏟斗卸料) 位置移至 HOLD (固定) 位置。 禁止在鏟斗油缸完全伸長的狀態下,將操縱桿維持在 BUCKET DUMP(鏟斗傾卸)位置 10 秒以上。
- 將調速器控制操縱桿移至最大引擎速度。 重複步驟 2。
如此可使機油達到釋放壓力,使機油更迅速到達工作溫度。
- 輪轉所有控制器,以計算所有液壓汽缸和液壓管線的熱機油量。
Show/hide table
當您輪流作動機器控制裝置時,機器可能會突然移動。 碰觸到機器和物體之間的人員或地面的人員會造成嚴重傷亡。 輪流作動機器控制裝置之前,機器必須位於 遠離外部物體和地面人員的無阻礙、無危險的作業區域。
- 進行操作期間,請持續觀察儀表和指示燈。
Caterpillar Information System:
H35E S, H45E S, H55E S and H65E S Hydraulic Hammers General Hazard Information
H35E S, H45E S, H55E S and H65E S Hydraulic Hammers Fire Prevention and Explosion Prevention
H35E S, H45E S, H55E S and H65E S Hydraulic Hammers Burn Prevention
M325D Material Handler Machine Systems Swing Gear and Bearing - Install
C15 and C18 Petroleum Generator Sets Reference Information
C7.1 Engines For Caterpillar Built Machines Engine Temperature Sensor Open or Short Circuit - Test
324E and 329E Excavators and 329E MHPU Mobile Hydraulic Power Unit C7.1 Engine Supplement Alternator - Remove and Install
324E and 329E Excavators and 329E MHPU Mobile Hydraulic Power Unit C7.1 Engine Supplement Fuel Manifold - Remove and Install
324E and 329E Excavators and 329E MHPU Mobile Hydraulic Power Unit C7.1 Engine Supplement Nozzle Heater Harness - Remove and Install - Harness Assembly
324E and 329E Excavators and 329E MHPU Mobile Hydraulic Power Unit C7.1 Engine Supplement Relay (ARD Nozzle Heater) - Remove and Install
336E Excavator and 336E MHPU Mobile Hydraulic Power Unit Machine Systems Main Control Valve - Assemble
340D Excavator Boom/Stick/Bucket Combinations
324E and 329E Excavators and 329E MHPU Mobile Hydraulic Power Unit C7.1 Engine Supplement Exhaust Elbow - Remove and Install
300.9D and 300.9D VPS Mini Hydraulic Excavator Bucket Tips - Inspect/Replace
300.9D and 300.9D VPS Mini Hydraulic Excavator Battery Electrolyte Level - Check
300.9D and 300.9D VPS Mini Hydraulic Excavator Main Relief Valve - Check
C7.1 Engines For Caterpillar Built Machines Fuel Pump Relay Circuit - Test
C7.1 Engines For Caterpillar Built Machines Glow Plug Starting Aid - Test
M313D, M315D, M315D Series 2, M315D2, M316D, M317D Series 2, M317D2, M318D, M320D2, M322D, M322D 2 MH, M322D2 and M324D 2 MH Wheeled Excavators Electronic System MID 039 - CID 1130 - FMI 05
C4.4 Industrial Engine Exhaust Elbow - Remove and Install - Top Mounted and Side Mounted Turbocharger Exhaust Elbow
C7.1 Engines For Caterpillar Built Machines Ignition Keyswitch Circuit and Battery Supply Circuit - Test
300.9D and 300.9D VPS Mini Hydraulic Excavator Coolant System - Flush
M313D, M315D, M315D Series 2, M315D2, M316D, M317D Series 2, M317D2, M318D, M320D2, M322D, M322D 2 MH, M322D2 and M324D 2 MH Wheeled Excavators Electronic System MID 039 - CID 1627 - FMI 05
M313D, M315D, M315D Series 2, M315D2, M316D, M317D Series 2, M317D2, M318D, M320D2, M322D, M322D 2 MH, M322D2 and M324D 2 MH Wheeled Excavators Electronic System MID 039 - CID 1627 - FMI 03