MID 039 - CID 1627 - FMI 03
产生此代码的情况:
Show/hide table
图 1 | g03876192 |
加油泵示意图(包括燃油泵继电器)。 |
该诊断代码与燃油泵继电器有关。 FMI 03 诊断代码表示 ECM 已确定继电器电路的电压高于正常值。
可能由于下列原因产生该诊断代码:
- 继电器出现故障。
- 继电器电源电路对蓄电池正极电路短路。
- 机器 ECM 有故障。 这种情况不太可能。
注: 以下测试步骤可能会生成其他诊断代码。 忽略生成的这些诊断代码,并在修复原有诊断代码后清除这些忽略的诊断代码。 执行本步骤之前,请确保诊断代码 CID 1627 FMI 03 为激活状态。
注: 使用 146-4080 数字式万用表 进行本步骤中的测量。
测试步骤 1. 检查继电器电源电路是否对蓄电池正极电路短路。
- 将钥匙起动开关和断路开关转到断开位置。
- 从机器 ECM 上断开机器线束接头。 从安装插座上断开继电器。
- 在开关面板的机器线束接头上,测量触点 C17-14(导线 T776-GY)与 ECM 的机器线束接头中使用的所有触点之间的电阻。
预期结果:
各电阻测量值都大于 5000 欧姆。
结果:
- 确定 - 各电阻测量值都大于 5000 欧姆。 机器线束正常。 转至测试步骤 2。
- 异常 - 各电阻测量值都不大于 5000 欧姆。 机器线束中存在短路。 C17-14(T776-GY)与电阻测量值低的电路之间存在短路。
修复: 修理或更换机器线束。
停止
测试步骤 2. 检查该诊断代码是否仍处于激活状态。
- 检查并清洁线束接头的触点。 检查并清洁继电器安装插座的触点。
- 重新连接所有线束接头。 将继电器安装到安装插座上。
- 将断路开关和钥匙起动开关转到接通位置。
- 操作机器。
- 确定 CID 1627 FMI 03 是否为激活状态。
预期结果:
CID 1627 FMI 03 为激活状态。
结果:
- 是 - CID 1627 FMI 03 为激活状态。 此故障没有得到排除。 ECM 可能出现故障。
修复: ECM 不太可能有故障。 先退出此步骤,然后重新执行此步骤。 如果没有找到该诊断代码的原因,则应更换 ECM。 参见测试和调整, "电子控制模块(ECM)- 更换 "。
停止
- 否 - CID 1627 FMI 03 为未激活状态。 此时不存在该故障。
修复: 原有诊断编码可能是由某个线束接头的电气连接不良或短路引起的。 使机器恢复正常运转。
停止
Caterpillar Information System:
M313D, M315D, M315D Series 2, M315D2, M316D, M317D Series 2, M317D2, M318D, M320D2, M322D, M322D 2 MH, M322D2 and M324D 2 MH Wheeled Excavators Electronic System MID 039 - CID 1627 - FMI 05
300.9D and 300.9D VPS Mini Hydraulic Excavator Coolant System - Flush
C7.1 Engines For Caterpillar Built Machines Ignition Keyswitch Circuit and Battery Supply Circuit - Test
C4.4 Industrial Engine Exhaust Elbow - Remove and Install - Top Mounted and Side Mounted Turbocharger Exhaust Elbow
M313D, M315D, M315D Series 2, M315D2, M316D, M317D Series 2, M317D2, M318D, M320D2, M322D, M322D 2 MH, M322D2 and M324D 2 MH Wheeled Excavators Electronic System MID 039 - CID 1130 - FMI 05
C7.1 Engines For Caterpillar Built Machines Glow Plug Starting Aid - Test
C7.1 Engines For Caterpillar Built Machines Fuel Pump Relay Circuit - Test
300.9D and 300.9D VPS Mini Hydraulic Excavator Main Relief Valve - Check
300.9D and 300.9D VPS Mini Hydraulic Excavator Battery Electrolyte Level - Check
300.9D and 300.9D VPS Mini Hydraulic Excavator Bucket Tips - Inspect/Replace
324E and 329E Excavators and 329E MHPU Mobile Hydraulic Power Unit C7.1 Engine Supplement Exhaust Elbow - Remove and Install
300.9D and 300.9D VPS Mini Hydraulic Excavator Engine and Machine Warm-Up
Procedure to Install Waste Handling Arrangement on Series D Wheeled Excavators{1353, 1356, 1360, 1386, 1387, 1408, 1931, 5057, 5061, 7000, 7255, 726A, 7272, 7490, 7600, 7601, 7610, 7620} Procedure to Install Waste Handling Arrangement on Series D Wheeled Excavators{1353, 1356, 1360, 1386, 1387, 1408, 1931, 5057, 5061, 7000, 7255, 726A, 7272, 7490, 7600, 7601, 7610, 7620}
300.9D and 300.9D VPS Mini Hydraulic Excavator Service Interval Chart
Wheeled Excavators Monitoring System Prestart Monitoring Function
300.9D and 300.9D VPS Mini Hydraulic Excavator System Pressure Release
2014/08/25 New Torque Specification for the Self-Locking Nut on the Rod Assembly of the Stick Cylinder for Certain Excavators {5458}
314E CR and 314E SR Excavator Systems General Information
301.4C Mini Hydraulic Excavator Battery or Battery Cable - Inspect/Replace
300.9D and 300.9D VPS Mini Hydraulic Excavator Engine Valve Lash - Check/Adjust
300.9D and 300.9D VPS Mini Hydraulic Excavator Fuel Injection Timing - Check/Adjust
300.9D and 300.9D VPS Mini Hydraulic Excavator Fuel Injection Pump - Clean/Adjust
300.9D and 300.9D VPS Mini Hydraulic Excavator Light - Test
300.9D and 300.9D VPS Mini Hydraulic Excavator Fasteners - Check