Pinion Clearance - Adjust
Bila solenoid sudah terpasang, lakukan penyetelan jarak bebas pinion. Penyetelan dapat dilakukan dengan motor starter dilepaskan.
Show/hide table
Ilustrasi 1 | g01364202 |
Koneksi untuk pemeriksaan jarak bebas pinion (1) Kabel negatif motor starter |
- Putuskan kabel negatif motor starter (1) dari terminal ground "G" (2) solenoid.
- Sambungkan baterai ke solenoid sesuai Gambar 1. Gambar 1 menunjukkan sistem 24 volt dengan dua baterai 12 volt yang tersambung secara seri ke motor starter. Sambungkan empat baterai 8 volt secara seri untuk sistem 32 volt. Sambungkan delapan baterai 8 volt secara seri untuk sistem 64 volt. Sambungkan sisi positif kabel baterai ke terminal "S" solenoid motor starter. Sambungkan sisi negatif kabel baterai ke terminal "G" motor starter.
- Sentuhkan sesaat kabel dari terminal "G" ke terminal "Mtr". Pinion akan berpindah ke posisi start dan pinion akan tetap di posisi itu sampai baterai dilepas.
Show/hide table
Ilustrasi 2 g01958306 Pemeriksaan jarak bebas pinion
(2) Mur penyetelan
(3) Sumbat
(4) Rumah penggerak pinion
(5) Pinion
(X) Jarak bebas pinion - Dorong pinion ke arah komutator untuk menghentikan gerakan bebas.
- Ukur jarak bebas (X) dari pinion ke rumah penggerak pinion. Jarak bebas pinion (X) harus sebesar
9.10 ± 0.8 mm (0.36 ± 0.03 inch) . - Jika jarak bebas tidak benar, lepaskan sumbat pada rumah tuas pemindah gigi (3). Putar mur pengatur (2) hingga jarak bebas sudah benar. Memutar mur searah jarum jam akan mengurangi jarak bebas (X).
Catatan: Plunger dapat berputar saat mur pengatur (2) diputar. Jika plunger berputar, putuskan baterai dari solenoid. Lepaskan solenoid dari motor starter. Tahan plunger agar tidak berputar dan setel mur (2). Prosedur ini mungkin harus dilakukan beberapa kali hingga diperoleh jarak bebas yang benar.
- Putuskan baterai dan pasang sumbat pada rumah tuas pemindah gigi.
Caterpillar Information System:
3608 Engine Generator Oil Level - Check
3608 Engine Generator Oil Filter - Change
Programmable Relay Control Module (PRCM) Display Codes
C175-16 Locomotive Engine Checking Engine Cylinders with an Electronic Service Tool
3608 Engine Generator Oil - Change
3524B Engines for 797 and 797B Off-Highway Trucks Fuel System Inspection
325D and 329D Excavators and 325D Material Handler Machine System Specifications Shuttle Valve (Pilot Lines)
3608 Engine Engine Oil Sample - Obtain
Programmable Relay Control Module (PRCM) Block Diagram
3608 Engine Air Starting Motor Lines Screen - Clean
C-10, C-12, 3406E, C-15, C-16 and C-18 Engines - Electronic PTO Installation and Application Component Installation
3500B Engines for Caterpillar Built Power Modules Turbocharger
SR4 and SR4B Electric Power Generation Rewind Data Winding Data for <B>7E-0097</B> Generator through <B>7E-9695</B> Generator
3608 Engine Air Prelube Pump Lubricator Bowl - Clean
3500B and 3500B High Displacement Generator Set Engines Measuring Inlet Manifold Pressure
2000/06/01 Special Instruction, REHS0589-01, "Emergency Stop Circuit Improvement for the Electronic Instrument Panel to Control Engine Restart" is Available {7451}
3524B Engines for 797 and 797B Off-Highway Trucks Crankcase Pressure
3508B Industrial Engine with an ADEM 2 Electronic Control Module Emergency Stop Switch (Remote)
SPT342 Truck Mounted Pumper Gauges and Indicators
3406E, C-10 and C-12 Truck Engines Severe Service Application - Check
Programmable Relay Control Module (PRCM) Electrical Connector - Inspect
3500 Engines For Caterpillar Built Power Modules Engine Oil Pressure is Low
Programmable Relay Control Module (PRCM) Connector Contact Identification
SR4 and SR4B Electric Power Generation Rewind Data Winding Data for <B>7W-1877</B> Generator through <B>7W-8825</B> Generator