Engine Rear Mount - Remove and Install
Removal Procedure
Show/hide table
Required Tools     | |||
Tool     | Part Number     | Part Description     | Qty     |
A     | 189-0409     | Shackle As     | 1     |
- Disconnect gas spring (2). Reposition and secure cover assembly (1) .
Show/hide table
Illustration 1 | g01309886 |
Show/hide table
Personal injury can result from being struck by parts propelled by a released spring force. Make sure to wear all necessary protective equipment. Follow the recommended procedure and use all recommended tooling to release the spring force. |
- Attach Tooling (A) and a suitable lifting device to the engine. Apply slight lifting tension to the engine. The weight of the engine is approximately 770 kg (1700 lb).
Show/hide table
Illustration 2 | g01309887 |
- Remove bolt (3) and washer (4). Remove bolts (5) and mount assembly (6). Remove plate (7) and spacer (8) .
Show/hide table
Illustration 3 | g01309888 |
Installation Procedure
Show/hide table
Required Tools     | |||
Tool     | Part Number     | Part Description     | Qty     |
A     | 189-0409     | Shackle As     | 1     |
- Install spacer (8) and plate (7). Install mount assembly (6) and bolts (5). Install washer (4) and bolt (3) .
Show/hide table
Illustration 4 | g01309888 |
- Remove Tooling (A) and the suitable lifting device from the engine.
Show/hide table
Illustration 5 | g01309887 |
- Position cover assembly (1). Connect gas spring (2) .
Show/hide table
Illustration 6 | g01309886 |
Show/hide table
Improper assembly of parts that are spring loaded can cause bodily injury. To prevent possible injury, follow the established assembly procedure and wear protective equipment. |
Caterpillar Information System:
M316D Wheeled Excavator C6.6 Engine Supplement Engine Front Mount - Remove and Install - Right Side
New Replacement Options for Serviced Engines{1000} New Replacement Options for Serviced Engines{1000}
M316D Wheeled Excavator C6.6 Engine Supplement Engine Enclosure Group - Remove and Install
2007/07/23 A New Relay Eliminates Issues of Hard Starting {1426}
303.5 Mini Hydraulic Excavator Bucket Tips - Inspect/Replace - J200 Tips
325C Excavator Maintenance Interval Schedule
C18 Engine for Caterpillar Built Machines Retarder - Test
C18 Engine for Caterpillar Built Machines Injector Solenoid - Test
C18 Engine for Caterpillar Built Machines Fuel Transfer Pump - Test
Installation of the Rotary Fuel Injection Pump{1251} Installation of the Rotary Fuel Injection Pump{1251}
3126 and C7 Oil Pan Gaskets{1302} 3126 and C7 Oil Pan Gaskets{1302}
C18 Engine for Caterpillar Built Machines Electrical Power Supply - Test
330D Forest Machine Machine Systems Final Drive and Travel Motor - Remove
323D Excavator Refrigerant Dryer - Replace
C6.6 Engines for Caterpillar Built Machines Fuel Priming Pump - Remove and Install - Mechanical Priming Pump
308D CR Mini Hydraulic Excavator Caterpillar Approved Work Tools
2007/07/16 An Improvement has been Made to the Bulk Material for Hose Assemblies {5057}
3412E Engine for Caterpillar Built Machines Sensor Signal (Analog, Active) - Test
320D Forest Machines Power Receptacle - If Equipped
303C CR, 303.5C CR, 304C CR and 305C CR Mini Hydraulic Excavators Bucket Tips - Inspect/Replace - Vertical Retention System for a Round Hole Tip
320D Forest Machines Specifications
GSH9B, GSH15B and GSH20B Orange Peel Grapples Grapple Link
320D Forest Machines Fuses - Replace
GSH9B, GSH15B and GSH20B Orange Peel Grapples Grapple Link