Inlet and Exhaust Valve Guides - Remove and Install
Removal Procedure
Show/hide table
| Required Tools | |||
| Tool | Part Number | Part Description | Qty |
| A | FT-2716 | Valve Guide Driver | 1 |
| B | FT-2717 | Stop Collar | 1 |
Start By:
- Remove the inlet valves and the exhaust valves. Refer to Disassembly and Assembly, "Inlet and Exhaust Valves - Remove and Install".
Show/hide table
 | |
| Illustration 1 | g00808012 |
Show/hide table
| NOTICE |
|---|
Keep all parts clean from contaminants. Contaminants may cause rapid wear and shortened component life. |
Show/hide table
 | |
| Illustration 2 | g00702790 |
- Use Tool (A) in order to remove the valve guides from the cylinder head.
- Repeat the procedure for the remaining valve guides.
Installation Procedure
Show/hide table
| Required Tools | |||
| Tool | Part Number | Part Description | Qty |
| A | FT-2716 | Valve Guide Driver | 1 |
| B | FT-2717 | Stop Collar | 1 |
Show/hide table
| NOTICE |
|---|
Keep all parts clean from contaminants. Contaminants may cause rapid wear and shortened component life. |
- Put the valve guide in position. Carefully tap the valve guide in order to start the installation. Use Tool (A) and Tool (B) to seat the valve guide in the cylinder head.
Show/hide table
 | |
| Illustration 3 | g00632176 |
Typical example | |
- Check the protrusion of the valve guides. The valve guides should protrude 7.70 to 7.85 mm (0.303 to 0.309 inch) above the valve spring recess.
- Repeat the procedure for the remaining valve guides.
Note: After installing the unfinished valve guides, you must ream the valve guides to the finished diameter. Refer to Specifications, "Cylinder Head Valves" for the finished diameter of the valve guides.
End By: Install the inlet valves and the exhaust valves. Refer to Disassembly and Assembly, "Inlet and Exhaust Valves - Remove and Install".
Caterpillar Information System:
3114, 3116, and 3126 Engines Gear Group (Front) - Time
SR4 and SR4B Electric Power Generation Rewind Data Winding Data for <B>129-1502</B> Generator through <B>129-5034</B> Generator
TK711, TK721, TK722 and TK732 Track Feller Bunchers Crushing Prevention and Cutting Prevention
2000/04/01 New Expansion Tank is now Available {1354}
2000/05/01 Check The Fuel Injection Control Linkage For A Loose Rivet {1298}
2001/05/01 Image Gallery CD-ROM Is Now Available For The Caterpillar HEUI HI300 And EUI Fuel Systems {1250}
2000/04/01 Image Gallery CD-ROM Is Now Available For The Caterpillar HEUI HI300 And EUI Fuel Systems {1250}
3114, 3116, and 3126 Engines Unit Injector Synchronization - Adjust
Connection Diagrams: SR4 and SR4B Generators, Voltage Regulators, Options Selection Guide for Voltage Regulator (SR4B for 3500 Engines)
325, 325B and 325L Excavators Final Drive Oil Sample - Obtain
2000/04/01 New Turbocharger Compressor Cover is now Available {1052}
3114, 3116, and 3126 Engines Unit Injector - Adjust
SR4 and SR4B Electric Power Generation Rewind Data Winding Data for <B>5N-7208</B> Generator through <B>5N-7232</B> Generator
325, 325B and 325L Excavators Final Drive
3034 Engine for Caterpillar Built Machines Inlet and Exhaust Valve Seat Inserts - Remove and Install
3114, 3116, and 3126 Engines for Caterpillar Built Machines Inlet Manifold - Remove
3114, 3116, and 3126 Engines for Caterpillar Built Machines Inlet Manifold - Install
325, 325B and 325L Excavators Final Drive
SR4 and SR4B Electric Power Generation Rewind Data Winding Data for <B>5N-7233</B> Generator through <B>5N-7309</B> Generator
3500B Engines for Caterpillar Built Power Modules with the ADEM 3 Electronic Control Module System Overview
2000/09/11 Use 159-9404 Counterbore Tool Group In Order to Bore Cylinder Block {0705, 1000}
C-10 and C-12 Industrial Engines Piston and Rings
2000/05/01 Check The Fuel Injection Control Linkage For A Loose Rivet {1298}
C-10, C-12, 3406E, C-15, C-16 and C-18 Engines - Electronic PTO Installation and Application PTO Shutdown Timer - Test