Housing (Front) - Install
安装步骤
Show/hide table
所需工具     | |||
工具     | 零件号     | 零件描述     | 数量     |
A     | 138-8440     | 部件清洁剂     | 1     |
B     | 169-5464     | 快速硫化底漆     | 1     |
C     | 1U-8846     | 密封垫密封胶     | 1     |
- 使用工具 (A) ,清洁前壳体 (4) 接合面。
Show/hide table
图 1 | g01011906 |
- 在接合面上涂抹工具 (B) 。 至少等待 3 到 5 分钟使底漆风干。
- 在接合面上涂抹工具 (C) 。 均匀地铺开密封胶。 涂抹密封胶后,必须在十分钟以内安装前壳体。
注: 不要让工具 (C) 密封住前壳体 (4) 上的主机油道。
- 将前壳体安置在缸体上。
- 安装将前壳体固定至缸体和发动机油底壳的螺栓 (5) 。
- 定位皮带张紧器 (3) ,然后安装螺栓 (1) 。
Show/hide table
图 2 | g01011903 |
- 安置发动机前支架并安装螺栓 (2) 。
- 如果配备,安装所有外部部件。
End By:
- 安装凸轮轴。 请参阅 拆解和组装, "凸轮轴 - 安装"。
- 安装曲轴前油封。 请参阅 拆解和组装, "曲轴前密封 - 安装"。
- 安装曲轴减振器。 请参阅 拆解和组装, "减振器和皮带轮 - 拆卸和安装"。
Caterpillar Information System:
3612 and 3616 Engines Vibration Damper
3612 and 3616 Engines Crankshaft Deflection (Bend)
3114, 3116, and 3126 Engines for Caterpillar Built Machines Air Compressor - Remove and Install
SR4 and SR4B Electric Power Generation Rewind Data Winding Data for <B>5N-0027</B> Generator through <B>5N-0050</B> Generator
325D and 329D Excavators Hydraulic System Relief Valve (Line)
3618 Engine Air Starting System Operation
3034 Engine for Caterpillar Built Machines Fuel Injection Lines
3618 Engine Test Tools for the Electrical System
2000/04/01 Correction to Parts Manual {1393}
3500 Generator Set Engines Lubrication
3618 Engine Pressure Regulating Valve
2000/04/01 Correction to Parts Manual {1393}
G3520B Engines Symptoms
3612 and 3616 Engines Pressure Regulating Valve
3612 and 3616 Engines Lubricator and Strainer
3612 and 3616 Engines Test Tools for the Electrical System
G3304 and G3306 Engines Battery
G3516B Engines Engine Will Not Crank
3126 Truck Engine Military Housing (Front) - Remove
3003, 3013, 3014 and 3024 Engines for Caterpillar Built Machines Flywheel Housing
3034 Engine for Caterpillar Built Machines Fuel Filter Base
G3516B Engines Engine Cranks but Will Not Start
G3516B Engines Engine Misfires, Runs Rough or Is Unstable
2000/03/01 190-02 "Loss of Engine RPM Signal" with an ADEM II ECM {1901, 1912}