Final Drive Carriers, Hubs and Brakes - Assemble - Rear Axle
组装步骤
Show/hide table
所需工具     | |||
---|---|---|---|
工具     | 零件号     | 零件描述     | 数量     |
A     | 1P-1863     | 挡圈钳     | 1     |
C     | 267-6564     | 扳手     | 1     |
J     | 4C-5593     | 防粘结剂     | 1     |
K     | 6V-6080     | 扭矩倍增器总成     | 1     |
L     | 269-7627     | 油封安装工具     | 1     |
Show/hide table
注意 |
---|
在检验、保养、测试、调整及维修发动机时,请小心确保盛接流出的液体。 在打开或拆解任何储有液体的部件之前,要准备好合适的容器收集液体。 有关适合收集和盛接卡特彼勒产品上的液体的工具和供应品,请参阅专门出版物, NENG2500, "卡特彼勒代理商工具目录"。 按照本地法规和条例处置所有液体。 |
- 将适当的起吊设备连接到轮毂 (31) 上。 轮毂 (31) 的重量约为 29 kg (65 lb)。 将轮毂 (31) 放置到位,然后安装螺栓 (32) 。 拧紧螺栓 (32) 至 280 N·m (207 lb ft) 的扭矩。
Show/hide table
图 1 | g01178432 |
- 加热轴承内圈 (30) ,然后安装轴承内圈 (30) 。
Show/hide table
图 2 | g01178643 |
- 安装隔套 (29) 。
Show/hide table
图 3 | g01178418 |
- 冷却轴承外圈 (28) ,然后安装轴承外圈 (28) 。
Show/hide table
图 4 | g01178644 |
- 使用工具 (L) 和适当的压具,将唇型密封 (27) 安装到法兰面 (26) 以下 6.0 + 0.2 - 0 mm (0.24 + 0.01 - 0 in) 的深度。
Show/hide table
图 5 | g01184452 |
- 将适当的起吊设备连接到法兰 (26) 上,然后安装法兰 (26) 。 法兰 (26) 的重量约为 38 kg (83 lb)。 加热轴承内圈 (25) ,然后安装轴承内圈 (25) 。
Show/hide table
图 6 | g01184454 |
- 拆下 O 形密封圈 (17) 、环 (18) 、O 形密封圈 (19) 和环 (20) 。
Show/hide table
图 7 | g01178414 |
- 将活塞 (16) 放置到位。 安装螺栓、弹簧和护圈 (15) 。 将螺栓拧紧至 11 N·m (8 lb ft) 的扭矩。
Show/hide table
图 8 | g01178412 |
Show/hide table
被弹簧力爆出的零件击中,会招致人员伤害。 确保穿上所有必要的保护装备。 遵照建议的程序,并使用所有建议的工具以释放弹簧力。 |
- 安装齿圈壳体 (14) 和短轴 (13) 。
Show/hide table
图 9 | g01185479 |
- 将工具 (J) 涂覆到螺母 (11) 上,然后安装螺母 (11) 。 使用工具 (C) 和工具 (K) 以拧紧螺母 (11) 。 拧紧螺母 (11) 至 1400 N·m (1033 lb ft) 的,以施加轴承预载。
Show/hide table
图 10 | g01184499 |
- 使用工具 (C) 拆下螺母 (11) 。 拆下齿圈壳体 (14) 。 拆下短轴 (13) 。
- 安装 O 形密封圈 (24) 。
Show/hide table
图 11 | g01178429 |
- 安装托架齿轮 (22) 和 O 形密封圈 (23) 。
Show/hide table
图 12 | g01178416 |
- 安装制动盘 (21) 。 安装过程中,交替安装摩擦片和主动盘。
Show/hide table
图 13 | g01178415 |
- 对准齿圈壳体 (14) 和轮毂 (31) 上的标记。 安装齿圈壳体 (14) 。 安装 O 形密封圈 (12) 和短轴 (13) 。
Show/hide table
图 14 | g01178651 |
Show/hide table
图 15 | g01184455 |
- 将工具 (J) 涂覆到螺母 (11) 上,然后安装螺母 (11) 。 使用工具 (C) 和工具 (K) 以拧紧螺母 (11) 。 拧紧螺母 (11) 至 1400 + 200 - 0 N·m (1033 + 148 - 0 lb ft) 的扭矩。
Show/hide table
图 16 | g01178652 |
- 向制动器施加 9997 kPa (1450 psi) 的压力。 测量齿圈壳体 (14) 表面与活塞 (16) 表面之间的距离。. 将此尺寸记录为尺寸 (A) 。
Show/hide table
图 17 | g01184456 |
Show/hide table
图 18 | g01136698 |
Show/hide table
图 19 | g01136707 |
- 释放制动器中的压力。 测量齿圈壳体 (14) 表面与活塞 (16) 表面之间的距离。. 将此尺寸记录为尺寸 (B) 。 用尺寸 (A) 减去尺寸 (B) ,以确定盘的间隙 (X) 。 盘的间隙 (X) 应为 1.2 mm (0.05 in) 至 1.8 mm (0.07 in)。 使用不同的圆盘,直到达到此间隙。
- 安装螺栓 (10) 。 拧紧螺栓 (10) 至 32 N·m (24 lb ft) 的扭矩。
Show/hide table
图 20 | g01178655 |
- 测量托架壳体 (2) 表面与止推垫圈座表面之间的距离。 将此尺寸记录为尺寸 (C) 。
Show/hide table
图 21 | g01136734 |
- 测量短轴 (13) 端面与法兰 (26) 安装面之间的距离。 将此尺寸记录为尺寸 (D) 。 用尺寸 (D) 减去 0.75 mm (0.0295 in),得到正确的端隙。
Show/hide table
图 22 | g01956539 |
Show/hide table
图 23 | g01136746 |
- 用尺寸 (C) 减去 (D) 。 所得的尺寸即是所需的止推垫圈的厚度。
- 使用适当的压具,安装止推垫圈。
- 安装滚柱轴承 (9) 、垫圈 (8) 和挡圈 (7) 。
Show/hide table
图 24 | g01136281 |
- 加热行星齿轮 (5) ,然后安装行星齿轮 (5) 。
Show/hide table
图 25 | g01138776 |
- 使用工具 (A) 安装挡圈 (4) 。
Show/hide table
图 26 | g01136274 |
- 将适当的起吊设备连接到托架壳体 (2) 上,然后将托架壳体 (2) 放置到位。 托架壳体 (2) 的重量约为 31 kg (68 lb)。
Show/hide table
图 27 | g01178408 |
- 安装螺栓 (3) 。 拧紧螺栓 (3) 至 55 N·m (41 lb ft) 的扭矩。
- 连接软管组件 (1) 。
- 给前终传动中注油。 请参阅操作和保养手册, "终传动机油 - 更换"。
End By: 安装后轮胎和轮缘。 请参阅 拆解和组装, "轮胎和轮辋 - 拆卸"。
Caterpillar Information System:
M318C and M322C Wheeled Excavators Power Train Final Drive Carriers, Hubs and Brakes - Disassemble - Rear Axle
302.5C Mini Hydraulic Excavator Machine Systems Cab - Install
Filtration Procedure for Hydraulic Oil in Compact Equipment {0680, 0768, 5050, 5056} Filtration Procedure for Hydraulic Oil in Compact Equipment {0680, 0768, 5050, 5056}
M318C and M322C Wheeled Excavators Power Train Tire and Rim - Install - Type II
M318C and M322C Wheeled Excavators Power Train Tire and Rim - Remove - Type II
324D Excavator Hydraulic System Return Hydraulic System
325C LCR Excavator Machine Systems Counterweight - Remove and Install
Bench Test Procedure for Hydraulic Piston Pumps{5070} Bench Test Procedure for Hydraulic Piston Pumps{5070}
C15 and C18 Engines for Caterpillar Built Machines Gear Group (Front)
325C LCR Excavator Machine Systems Evaporator Coil - Install
302.5C Mini Hydraulic Excavator Machine Systems Cab - Remove
302.5C Mini Hydraulic Excavator Machine Systems Main Control Valve - Assemble
C9.3 Tier 4 Final Engines Engine Oil Pressure Sensor
325C LCR Excavator Machine Systems Final Drive - Disassemble
325C LCR Excavator Machine Systems Swivel - Disassemble
325C LCR Excavator Machine Systems Swivel - Assemble
C27 and C32 Engines for Caterpillar Built Machines Coolant Temperature Sensor
325C LCR Excavator Machine Systems Manual Valve (Auxiliary Shutoff) - Remove
325C LCR Excavator Machine Systems Manual Valve (Auxiliary Shutoff) - Install
325C LCR Excavator Machine Systems Control Valve (Auxiliary) - Remove
325C LCR Excavator Machine Systems Control Valve (Auxiliary) - Install
C7 and C9 Engines for Caterpillar Built Machines Injector Trim File
325C LCR Excavator Machine Systems Main Control Valve - Remove
325C LCR Excavator Machine Systems Main Control Valve - Install