Swing Speed and Swing Drift on a Slope - Check
Measuring the swing speed on a slope will determine if there is a need to check the swing motor and the anti-reaction valve. Measuring the swing drift on a slope will determine if there is a need to check the swing parking brake.
Note: The engine speed and/or the machine configuration that is used during this test can affect the results of this test. Refer to Testing and Adjusting, "Engine Performance - Test" for the engine speed that was used for this test. Refer to Testing and Adjusting, "Operational Checks" for the machine configurations that were used for this test.
Note: The relief valve pressure settings must be set to the relief valve pressure specification before performing this operational check. Refer to Testing and Adjusting, "Specifications".
Show/hide table
Required Tools     | ||
---|---|---|
Part Number     | Description     | Qty     |
5P-3277     | Measuring Tape     | 1     |
    | Stopwatch     | 1     |
Show/hide table
Illustration 1 | g00298078 |
- Complete the following steps in order to measure the swing speed on a slope.
- The work tool should be empty.
- Position the machine on a slope of 12 degrees. Refer to Illustration 1.
- Position the implements at maximum reach and close the work tool. Position the work tool above the ground so that the work tool will not come in contact with any obstacles.
- Position the upper structure at position (A). The upper structure should be at a 90 degree angle to the lower structure. Refer to Illustration 2.
Show/hide tableIllustration 2 g00298079
- Measure the time that is required to swing the upper structure from position (A) to position (B) .
- Position the upper structure at position (C). The upper structure should be at a 90 degree angle to the lower structure.
- Measure the time that is required to swing the upper structure from position (C) to position (B).
Show/hide table
Table 2 Swing Time (seconds)     Item     New     Rebuild     Service Limit     Right Swing     5.2 or less     5.7 or less     6.5 or less     Left Swing    
- Complete the following steps in order to measure the swing drift on a slope.
- Position the upper structure at position (A). The upper structure should be at a 90 degree angle to the lower structure. Refer to Illustration 3.
Show/hide tableIllustration 3 g00298079
- To indicate the relationship of the two positions, put a mark (C) on the inner race and the outer race of the swing bearing. Refer to Illustration 4.
Show/hide tableIllustration 4 g00293972
(A) Upper frame
(B) Undercarriage frame
(C) Marking
- Stop the engine.
- Leave the machine in this position for three minutes. Measure the swing drift on the circumference of the swing bearing.
- Start the engine.
- Position the upper structure at position (C). The upper structure should be at a 90 degree angle to the lower structure. Refer to Illustration 3.
- Repeat Steps 2.b through 2.d.
Show/hide table
Swing Drift mm (inch)     | |||
---|---|---|---|
Item     | New     | Rebuild     | Service Limit     |
Right Swing     | 0     | 0     | 0     |
Left Swing     |
Caterpillar Information System:
330C Excavator Hydraulic System Swing Speed and Overswing on Level Ground - Check
330C Excavator Hydraulic System Machine Drift on a Slope - Check
345C Material Handler Hydraulic System Return Hydraulic System
330C Excavator Hydraulic System Travel on Level Ground - Test
365C Front Shovel Hydraulic System Cylinder Drift - Check - Loaded Bucket
330C Excavator Hydraulic System Travel on Level Ground - Test - Optional Test
345B Series II Excavator Additional Messages
330C Excavator Hydraulic System Engine Performance - Test - Engine Speed
VHS10, VHS30, VHS40, VHS50, VHS60 and VHS70 Work Tools Cutters - Inspect/Replace
330C Excavator Hydraulic System Main Hydraulic Pump Air - Purge
330C Excavator Hydraulic System Hydraulic System Pressure - Release
302.5C Mini Hydraulic Excavator Machine System Specifications Blade Lift Cylinder
330C Excavator Hydraulic System Relief Valve (Pilot) - Test and Adjust
330C Excavator Hydraulic System Accumulator (Pilot) - Test and Charge
330C Excavator Hydraulic System Relief Valve (Main) - Test and Adjust
330C Excavator Hydraulic System Swing Motor - Test - Measurement of Case Drain Oil
330C Excavator Hydraulic System Relief Valve (Swing) - Test and Adjust
302.5C Mini Hydraulic Excavator Machine System Specifications Stick Cylinder
345C Excavator Tool Control System System 14: Solenoid Valve (Proportional Reducing) - Calibrate - Attachment Control Valve
345C Excavator Tool Control System System 14: Relief Valve (Line) - Test and Adjust - Attachment Control Valve
345C Excavator Tool Control System System 14: Relief Valve (Main) - Test and Adjust - Auxiliary Control Valve (Medium Pressure)
330C With Drilling Front Machine System Specifications Cooling Lines
365C Front Shovel Hydraulic System Relief Valve (Line) - Test and Adjust
365C Front Shovel Hydraulic System Specifications