Cylinder Drift - Check - Loaded Bucket
Note: The engine speed and/or the machine configuration that is used during this test can affect the results of this test. Refer to Testing and Adjusting, "Engine Performance - Test" for the engine speed that was used for this test. Refer to Testing and Adjusting, "Operational Checks" for the machine configurations that were used for this test.
Note: The relief valve pressure settings must be set to the relief valve pressure specification before performing this operational check. Refer to Testing and Adjusting, "Specifications".
Show/hide table
Required Tools     | ||
---|---|---|
Part Number     | Description     | Qty     |
5P-3277     | Measuring Tape     | 1     |
    | Stopwatch     | 1     |
Show/hide table
Illustration 1 | g00865263 |
- Load the bucket.
- Position the machine on level ground. Refer to Illustration 1.
- Fully extend the stick cylinder.
- Fully extend the bucket cylinder.
- Raise the boom until the stick to bucket pin is the same height as the boom foot pin.
- Measure each cylinder's length from cylinder pin to cylinder pin.
- Stop the engine.
- Leave the machine in this position for three minutes. Measure each cylinder's length from cylinder pin to cylinder pin for drift.
Show/hide table
Cylinder Drift (Loaded Bucket)     | |||
---|---|---|---|
Item     | New     | Rebuild     | Service Limit     |
Boom Cylinder     | 6.0 mm (0.24 inch) or less     |
12.0 mm (0.47 inch) or less     |
24.0 mm (0.94 inch) or less     |
Stick Cylinder     | 12.0 mm ( 0.47 inch) or less     |
18.0 mm ( 0.71 inch) or less     |
30.0 mm ( 1.18 inch) or less     |
Bucket Cylinder     | 30.0 mm ( 1.18 inch) or less     |
45.0 mm ( 1.77 inch) or less     |
75.0 mm ( 2.95 inch) or less     |
Caterpillar Information System:
330C Excavator Hydraulic System Travel on Level Ground - Test - Optional Test
345B Series II Excavator Additional Messages
330C Excavator Hydraulic System Engine Performance - Test - Engine Speed
VHS10, VHS30, VHS40, VHS50, VHS60 and VHS70 Work Tools Cutters - Inspect/Replace
330C Excavator Hydraulic System Main Hydraulic Pump Air - Purge
330C Excavator Hydraulic System Hydraulic System Pressure - Release
302.5C Mini Hydraulic Excavator Machine System Specifications Blade Lift Cylinder
C9 Engines for Caterpillar Built Machines Cooling System - Test
302.5C Mini Hydraulic Excavator Machine System Specifications Swing Boom Cylinder
C9 Engines for Caterpillar Built Machines Lubrication System
C15 and C18 Engines for Caterpillar Built Machines CID 1421 FMI 09 Unable to communicate with Rear Engine ECM
C9 Engines for Caterpillar Built Machines General Information
330C Excavator Hydraulic System Travel on Level Ground - Test
345C Material Handler Hydraulic System Return Hydraulic System
330C Excavator Hydraulic System Machine Drift on a Slope - Check
330C Excavator Hydraulic System Swing Speed and Overswing on Level Ground - Check
330C Excavator Hydraulic System Swing Speed and Swing Drift on a Slope - Check
330C Excavator Hydraulic System Relief Valve (Pilot) - Test and Adjust
330C Excavator Hydraulic System Accumulator (Pilot) - Test and Charge
330C Excavator Hydraulic System Relief Valve (Main) - Test and Adjust
330C Excavator Hydraulic System Swing Motor - Test - Measurement of Case Drain Oil
330C Excavator Hydraulic System Relief Valve (Swing) - Test and Adjust
302.5C Mini Hydraulic Excavator Machine System Specifications Stick Cylinder
345C Excavator Tool Control System System 14: Solenoid Valve (Proportional Reducing) - Calibrate - Attachment Control Valve